N7201A652E - 第380页

NPM- TT2 EJM1E E-MB-05O-05 Unit setting Option setting 2 Setting information 2 5-1-1 -3 Operating procedure 5-1-1 ● Default ： OFF ■ Whole No. Item name Function when [ON] is sel ected 16 Keep PCB recog lamp, changing dat…

100%1 / 512
NPM-TT2 EJM1EE-MB-05O-05
5-1-1-2
Setting information 1
System
administration
●Default：OFF
■Whole
No. Item name Function when [ON] is selected
1 Quality trace
Transfers the log files including pickup/mounting orders and correction values
to the LNB during automatic operation.
2
Comm. abnormality
MC stop
Stops the NPM machine if communication with the LNB is broken.
3
Operation mode
Switch SD
Displays a message requesting the key disk (SD) when an attempt is made to
switch the operation mode to Engineer. Insert the key disk to switch to the
Engineer mode.
4 Parts trace
Sends the parts trace information to the LNB once the operation is started.
The information to be sent include the part information that is written to the
tape feeders whenever production of a PC board has been finished, and the
mounted part information by mounting point.
5 Screen print SD output Pressing the print screen switch saves the screenshot onto an SD card.
6
Empty Parts Auto
Screen Transition
If a “parts empty” error has occurred, the display automatically switches to the
reminder monitor screen of the part component concerned.
7
Empty Parts Auto
Screen Transition
(with stock)
If a “parts empty” error has occurred, the display automatically switches to the
reminder monitor screen of the part component concerned.
8
Auto product change
(option)
Performs production changeover (loading production data, replacing nozzles
and support pins, and adjusting the conveyor rail width, etc.) automatically.
9
Auto product change
PCB bar code recog
(option)
Recognizes barcodes on PCBs by the head camera to perform production
changeover automatically.
10
In again when auto
product change
Permits the production data to be downloaded when switching the production
data in cases where the ‘Auto product change’ function is used and defective
PC boards are reloaded after repair.
11
NG part Eject before
mounting
Ejects parts judged to be NG such as pickup error, recognition error or raised
lead, before mounting.
12
Production information
not picking up
management
Counts up all pickups attempted including parts empty and empty pockets of
the spliced tape feeders.
13
When feeder pickup
error happened.
Pickup error count
Counts up all unsuccessful pickups including those caused by parts empty
and empty pockets of the spliced tape feeders as pickup error.
14
When parts for one
piece of PCB is being
supplied, restart
operation
When the machine has stopped due to a “parts empty” error, this option
allows production to be resumed by just replenishing at least one of the
exhausted feeders.
15
Mount speed escape
action
Allows the X/Y-axis to be retracted at the mounting speed for the part being
picked up when the machine has comes to a single stop due to a cushion end
error or mounting error.
NPM-TT2 EJM1EE-MB-05O-05
Unit
setting
Option setting 2
Setting information 2
5-1-1-3
Operating procedure
5-1-1
● Default ：OFF
■Whole
No. Item name Function when [ON] is selected
16
Keep PCB recog lamp,
changing data
Keeps using the lamp value recorded in the machine, without performing
auto lamp teaching at PCB recognition during production changeover for
each machine.
17
PCB recognition lamp value
communication set
Applies the lamp value recorded in the upstream machine to all
downstream machines, without performing auto lamp teaching at PCB
recognition during production changeover for each machine.
18
Return action
(when production schedule
pieces are completed)
Returns the nozzles and trays at the end of automatic operation after the
scheduled production is reached.
19
Style and pickup angle set
freely
Enables the tape / stick feeder or tray style (angle) and tray pickup angle
(for 2-/3-nozzle heads only) to be set in 1-degree increments.
20
Vacuum sensor error
opposing lane product
continue
If, in the independent mounting mode, the machine comes to a single
stop due to mounting error or vacuum sensor error caused by dropped
part, this option allows the opposing lane to continue production.
21 Auto log off in production Enables the automatic log off function during production.
22
Transfer error opposing
lane product continue
Allows production on the opposing lane to continue even if a PCB
transfer, pickup, or position error has occurred.
23
PCB warp clamp 0
calibration
Generates the curved surface for PCB warp correction with the heights
of clamp positions as 0.
24
Change parts gap action
(short distance)
Sets the range of measurement with the [Parts gap confirm] button on
the Parts recog. teach screen to “100 x 100 mm”.
25
Remote Control
(Option)
Enables the remote control function by the host system.
26
Remote Production Start
(Option)
Enables remote production start with the remote control function.
Production starts by the production start instruction from the host
system.
27
LM Operation Message
(Option)
Shows the information or instruction messages from the host system on
the machine screen.
28
Distribution eject box
(Option)
Carries defective components separately to the ejection box specified in
the data.
29
Supply position fix when
recovery
Picks up parts from the feeder at the supply position determined by
optimization when performing recovery mounting after a parts empty or
pickup error.
30
Head camera barcode
recognition
When communication between MC and PCB barcode reading from the
head camera is ON in NPM^ require the PCB information from LNB
according to the PCB barcode.
NPM-TT2 EJM1EE-MB-05O-05
Setting information 3
System
administration
5-1-1-4
● Default ：OFF
■Whole
No. Item name Function when [ON] is selected
31
Pre-pickup Inspection
(Option)
Check the supplied components before picking them up.
32
Save whole image of the
pre-pickup inspection
(Option)
Saves the entire image of the specified component during the pre-pickup
inspection.
33
No recog and PCB pass
when PCB recog Error.
Shows the [No recog] and [PCB pass] buttons on the PCB recognition error
screen.
34
Pickup miss count in the
start up tape status
Includes the pickup errors occurred during tape feed start in the Pickup
count and Pickup error count in the Production report.
35
Recognition history LNB
transfer during error stop
Transfers the recognition history to the LNB when the machine has stopped
due to an error.
36
Split and output recipe
per lot
Divides the production data to be output lot by lot. Set this option to ON
when the “Output production data divided lot by lot” is ON in the DGS
production data setting.
37
In production Product
manage information
display
Production management information can be referred to during automatic
operation (without interrupting the machine).
However, if it is displayed during automatic operation, an error screen such
as the PCB recognition error screen cannot be displayed. The error screen
is displayed at the timing when you go back to the screen in production
from the production management information screen.
38
PCB ID confirm during
auto running resume
If you exit automatic operation halfway through the mounting process that
uses production data based on PCB ID scanning, the machine recognizes
the PCB barcode using its head camera and confirms PCB ID before
resuming automatic operation. The machine comes to an error stop if the
PCB located at the mounting position at the time of exit from automatic
operation is not identical in PCB ID (PCB info) to the one recognized, as
mentioned above, using the head camera. In such case, putting the former
back in the mounting position allows the machine to resume automatic
operation.
39
Parts Empty Warning
Auto Screen Transition
It is available only when [Empty Parts Auto Screen Transition] or [Empty
Parts Auto Screen Transition(with stock)] is on. If this parameter is ON it
will also transfer to production remaining monitor screen(machine)
automatically when parts empty warning
40
NG part Eject before
mounting (MntPosMov)
This function is only aimed at 16 nozzle head. After ending the parts
recognition if there are parts judged as pickup error or recognition error or
lead float after moving the mount position without executing the mount
action eject the parts and execute the mount action again when it is ON and
eject the parts after the mount action when it is OFF. (The error parts still
pass on the PCB even if it is ON.)
41
Production data DL by
Form Reading
According to reading the barcode from the wired scanner of first equipment
select the next production program and download to equipment.