N7201A652E - 第381页

NPM- TT2 EJM1E E-MB-05O-05 Setting information 3 System administration 5-1-1 -4 ● Default ： OFF ■ Whole No. Item name Function w hen [ON] is selec ted 31 Pre-pic kup Inspection (Option) Check the supplied compo nent s be…

NPM-TT2 EJM1EE-MB-05O-05

Unit

setting

Option setting 2

Setting information 2

5-1-1-3

Operating procedure

5-1-1

● Default ：OFF

■Whole

No. Item name Function when [ON] is selected

Keep PCB recog lamp,

changing data

Keeps using the lamp value recorded in the machine, without performing

auto lamp teaching at PCB recognition during production changeover for

each machine.

PCB recognition lamp value

communication set

Applies the lamp value recorded in the upstream machine to all

downstream machines, without performing auto lamp teaching at PCB

recognition during production changeover for each machine.

Return action

(when production schedule

pieces are completed)

Returns the nozzles and trays at the end of automatic operation after the

scheduled production is reached.

Style and pickup angle set

freely

Enables the tape / stick feeder or tray style (angle) and tray pickup angle

(for 2-/3-nozzle heads only) to be set in 1-degree increments.

Vacuum sensor error

opposing lane product

continue

If, in the independent mounting mode, the machine comes to a single

stop due to mounting error or vacuum sensor error caused by dropped

part, this option allows the opposing lane to continue production.

21 Auto log off in production Enables the automatic log off function during production.

Transfer error opposing

lane product continue

Allows production on the opposing lane to continue even if a PCB

transfer, pickup, or position error has occurred.

PCB warp clamp 0

calibration

Generates the curved surface for PCB warp correction with the heights

of clamp positions as 0.

Change parts gap action

(short distance)

Sets the range of measurement with the [Parts gap confirm] button on

the Parts recog. teach screen to “100 x 100 mm”.

Remote Control

(Option)

Enables the remote control function by the host system.

Remote Production Start

(Option)

Enables remote production start with the remote control function.

Production starts by the production start instruction from the host

system.

LM Operation Message

(Option)

Shows the information or instruction messages from the host system on

the machine screen.

Distribution eject box

(Option)

Carries defective components separately to the ejection box specified in

the data.

Supply position fix when

recovery

Picks up parts from the feeder at the supply position determined by

optimization when performing recovery mounting after a parts empty or

pickup error.

Head camera barcode

recognition

When communication between MC and PCB barcode reading from the

head camera is ON in NPM^ require the PCB information from LNB

according to the PCB barcode.

NPM-TT2 EJM1EE-MB-05O-05

Setting information 3

System

administration

5-1-1-4

● Default ：OFF

■Whole

No. Item name Function when [ON] is selected

Pre-pickup Inspection

(Option)

Check the supplied components before picking them up.

Save whole image of the

pre-pickup inspection

(Option)

Saves the entire image of the specified component during the pre-pickup

inspection.

No recog and PCB pass

when PCB recog Error.

Shows the [No recog] and [PCB pass] buttons on the PCB recognition error

screen.

Pickup miss count in the

start up tape status

Includes the pickup errors occurred during tape feed start in the Pickup

count and Pickup error count in the Production report.

Recognition history LNB

transfer during error stop

Transfers the recognition history to the LNB when the machine has stopped

due to an error.

Split and output recipe

per lot

Divides the production data to be output lot by lot. Set this option to ON

when the “Output production data divided lot by lot” is ON in the DGS

production data setting.

In production Product

manage information

display

Production management information can be referred to during automatic

operation (without interrupting the machine).

However, if it is displayed during automatic operation, an error screen such

as the PCB recognition error screen cannot be displayed. The error screen

is displayed at the timing when you go back to the screen in production

from the production management information screen.

PCB ID confirm during

auto running resume

If you exit automatic operation halfway through the mounting process that

uses production data based on PCB ID scanning, the machine recognizes

the PCB barcode using its head camera and confirms PCB ID before

resuming automatic operation. The machine comes to an error stop if the

PCB located at the mounting position at the time of exit from automatic

operation is not identical in PCB ID (PCB info) to the one recognized, as

mentioned above, using the head camera. In such case, putting the former

back in the mounting position allows the machine to resume automatic

operation.

Parts Empty Warning

Auto Screen Transition

It is available only when [Empty Parts Auto Screen Transition] or [Empty

Parts Auto Screen Transition(with stock)] is on. If this parameter is ON it

will also transfer to production remaining monitor screen(machine)

automatically when parts empty warning

NG part Eject before

mounting (MntPosMov)

This function is only aimed at 16 nozzle head. After ending the parts

recognition if there are parts judged as pickup error or recognition error or

lead float after moving the mount position without executing the mount

action eject the parts and execute the mount action again when it is ON and

eject the parts after the mount action when it is OFF. (The error parts still

pass on the PCB even if it is ON.)

Production data DL by

Form Reading

According to reading the barcode from the wired scanner of first equipment

select the next production program and download to equipment.

NPM-TT2 EJM1EE-MB-05O-05

5-1-1-5

Setting information 4

Unit

setting

Option setting 3

Operating procedure

5-1-1

No. Item name Function when [ON] is selected

Nozzle 2D code

recog

Detects wrong nozzle setting and checks for proper orientation of nozzle on

the nozzle changer by recognizing the 2D code on the nozzle at the start of

automatic operation.

Can't use the Nzl

without 2D Code

Causes the machine to stop if nozzles without 2D code are mixed up.

2D code recognition

only when nozzle

exchange

Causes the head camera to skip 2D code recognition of all nozzles set in the

nozzle changer when restarting the machine that has been stopped during

production.

Temperature warning

check

Compares the current temperature of adhesive with the preset value on the

temperature control unit.

Inside changer auto

arrange

Rearranges the nozzles on the nozzle changer according to the data after

recognizing the nozzle 2D code.

Bad mark recognition

judge value is

variable

Uses the criterion value in the bad mark information to judge the bad mark

recognition for production boards.

Bad nozzle auto

change

If a certain nozzle is determined to be bad due to “Bad nozzle error rate”, this

option replaces the nozzle concerned with a normal one automatically. (12-

/16-nozzle heads)

Continue to product

when stuff detect

Allows production to be continued even after an error has occurred due to

detection of stuffed nozzle or filter.

Big nozzle manual

change (front side)

Enables the nozzles to be set manually without replacing them automatically.

Big nozzle manual

change (rear side)

Enables the nozzles to be set manually without replacing them automatically.

No. Item name Function when [ON] is selected

1 Bad XY axis(front) Disables the front XY unit.

2 Bad XY axis(rear) Disables the front XY unit.

Time-lapse change

calibration during

producing of one

piece

Performs time-lapse change calibration during production of one PCB.

● Default ：OFF

■ XY-axis

● Default ：OFF

■ Head