CP-842E-842ME System Reference-SYS-CP842-10E - 第210页
System Installation and Upgrade >> System Installation 7-4 SYS-CP842-1.0E [Power] Screen Specify the [Power] screen settings as shown below . Power Savings: [Disabled] Idle Mode: Off Standby Ti meout: Off Auto Susp…
System Installation
and Upgrade >> System Installation
SYS-CP842-1.0E 7-3
[Advanced] Screen
Specify the [Advanced] screen settings as shown below.
I/O Device Configuration
PCI Configuration
Installed O/S: Other
Reset Configuration Data: Yes*1
Secured Setup Configurations:No
Large Disk Access Mode: DOS
PS/2 Mouse: Auto Detect
Legacy USB Support: Disabled
Halt on Watchdog Timer:Disabled
Watchdog Timer Interrupt:Auto
Go to the ‘‘I/O Device Configuration sub-menu by selecting the item and pressing
[Enter], then verify that the settings are as shown below.
Local Bus IDE adapter: Both
Serial port A: Auto
Serial port B: Auto
Parallel port: Disabled
Floppy Disk controller: Disabled*2
Onboard Ethernet controller: Enabled
Onboard USB controller: Disabled
Note: *1 : The Reset Configuration Data item is reset to No when the BIOS settings are completed,
and must therefore be set to Yes each time the BIOS Settings screen is displayed.
*2 : Set the “Floppy Disk Controller” to “Enabled” when using the optional floppy disk drive.
Go to the ‘‘PCI Configuration sub-menu by selecting the item and pressing [Enter],
then verify that the settings are as shown below.
PCI IRQ line 1: 11
PCI IRQ line 2: 5
PCI IRQ line 3: 10
PCI IRQ line 4: 9
System Installation
and Upgrade >> System Installation
7-4
SYS-CP842-1.0E
[Power] Screen
Specify the [Power] screen settings as shown below.
Power Savings: [Disabled]
Idle Mode: Off
Standby Timeout: Off
Auto Suspend Timeout: Off
Hard Disk Timeout: Disabled
Resume On time: [Off]
Resume time: [00:00:00]
Resume Date: [00/00/0000]
[BIOS] Screen
The [Bios] screen shows various types of information, but settings at this screen can-
not be changed.
[Boot] Screen
Arrange the order of the items as shown below. To change an items order, select the
item (highlighted), then use the [+] and [-] keys to move the item up and down, respec-
tively.
To avoid a startup from the floppy disk (in systems with a floppy disk drive), select
Removable Devices, then press [Shift] + [1] to enter an exclamation mark (!) in front of
Removable Devices as shown below.
! Removable Devices
ATAPI CD-ROM Drive
Hard Drive
Network Boot
[Exit] Screen
When the settings described above have been made, select the first item Exit Saving
Changes and press [Enter] key. Select Yes at the confirmation message to register the
settings.
System Installation
and Upgrade >> System Installation
SYS-CP842-1.0E 7-5
7.1.2 Installing the Operating System
The System Software Recovery Media CD-ROM is used to install the system software.
1 At the exit dialog box for the BIOS settings, insert the System Software Recov-
ery Media CD-ROM into the CD drive, then select [Yes] at the dialog box. When
the BIOS setting operation is ended in this manner (with CD-ROM inserted),
the system software installer is automatically started, and installation begins.
2 When the installer begins, the license information of the Easy-Restore used for
the system recovery displays together with the message, Strike a key when
ready at the bottom of the screen. Press the SPACE key to proceed. Press the
SPACE key three times to reach the end of the license information and the
installer.
When the operating system installation is complete, a dialog box displays ask-
ing you to reboot ([Reboot] button displays).
3 Do not select reboot yet because you must replace the System Software Recov-
ery Media with the machine control software CD-ROM first. (Proceed to next
section Installing the Machine Control Software.)
Note: Do not restart with the System Software Recovery Media CD-ROM inserted, as this
will reinstall Windows NT.