CP-842E-842ME System Reference-SYS-CP842-10E - 第33页
The Machine >> Machine Overview SYS-CP842-1.0E 3-11 3.1.5 T ouch Screen The operator issues commands to the machine from the touch screen at the front or rear of the machine. Each screen that appears at the t ouch …
The Machine >> Machine Overview
3-10
SYS-CP842-1.0E
START button
This button is pushed to commence operation. This button can only be pushed when
the machine is in START ready status (i.e., when the button is flashing).
CYCLE STOP button
This button can be used during operation to stop the machine at the end of the current
movement. Unlike the EMERGENCY STOP button, pressing CYCLE STOP does not
cut the 200V power.
READY ON button
This button cancels an error status and resupplies the 200V power to the servo sys-
tem.
EMERGENCY STOP button
Pressing an EMERGENCY STOP button cuts the 200V power to the machine and
stops operation immediately. This button locks in position when pressed, and must be
turned clockwise to release it.
Users should familiarize themselves with the locations of the EMERGENCY STOP
buttons prior to operating the machine. In addition to the button on the front of the
machine (shown in the figure above), further EMERGENCY STOP buttons are posi-
tioned at the rear of the machine, and on the optional MTU safety fence.
Refer to the illustration in Chapter 5 of the Safety Guidelines to confirm the positions
of all the EMERGENCY STOP buttons.
Side 1/2 ENABLE/LOCK switch
Toggle this switch to enable operation at the desired side; front (Side 1) or rear (Side
2), of the machine. Operation at a given side of the machine cannot be enabled if the
switch at the other side of the machine is set to LOCK.
Power Off button (touch screen command that displays when the EMERGENCY
STOP button is pushed)
The [Power Off] button is used to turn off the main power to the machine.
This button can only be pressed after the EMERGENCY STOP button has been
pushed.
The Machine >> Machine Overview
SYS-CP842-1.0E 3-11
3.1.5 Touch Screen
The operator issues commands to the machine from the touch screen at the front or
rear of the machine. Each screen that appears at the touch screen contains a number
of command buttons, which display the commands associated with the selection.
Some screens, as in the example below, are divided into sections with related com-
mands being grouped together.
Although different commands display at each screen, the title bar, information bar,
and command bar commands which are common to all screens (sections A to M in the
figure below) are explained below. Refer to part 3 of this manual for a detailed expla-
nation of the command hierarchy.
Title bar
A:Press the [FUJI] button to display version information for the machine control
software, vision system software, and operating system.
B:The name of the active program displays at this section of the title bar.
C:The name of the current screen displays at this section of the title bar.
D:This button displays in red if an error occurs. When red, this button can be
pressed at any screen to return to the red error screen.
Main area
E:The command buttons in the main section of each screen can be pressed to access
further related commands. Refer to part 3 for a detailed explanation of the com-
mand hierarchy.
F:The [Close] button is available on all screens except the [Main] screen. Press this
button once to return to the previous screen. Press this button in succession to
return to the [Main] screen.
Command section
Screen name
Command section
Select a command.
Command section
COMMAND COMMAND COMMAND
COMMAND
COMMAND
COMMAND
Close
COMMAND COMMAND
COMMAND COMMAND
COMMAND
FRONT
Vision
0
Host Servo Count
Operator CallABC_PROG Error
JOG:XY CAM
Title bar
Main area
Infomation bar
Command bar
C73OM008a
A B CD
E
F
G
H
I
J
K LM
Set Switch
The Machine >> Machine Overview
3-12
SYS-CP842-1.0E
Information bar
G:Messages display in this area of the information bar relating to the main proce-
dures associated with the screen above.
H:This displays either FRONT or REAR depending on which side of the machine is
currently set as the active side at which commands at the touch screen can be
used. To change the active side it is necessary to move the side selection switch
on the machine to ENABLE.
Command bar
I:Press the [Set Switch] button to display the [Parts Set Switch] screen. This
switch is used in place of the standard hardware switch to confirm that the set-
ting of parts is complete.
J:Press the [Vision] button to display a screen at which one of the three cameras
can be selected. When a camera button is pressed the raw image acquired by
that camera displays on screen.
K:Press the [Host] button to display a screen at which the communication and con-
trol status can be specified.
L:Press [Servo Count] to display the [Servo Count] screen. This displays readings
in mm/deg. or pulses for each of the eleven axes on the machine.
M:Press [Jog:] to display a screen at which inching speed and other settings can be
made. The button carries the name of the selected axis combination which will
move when the inching controls are used.