CP-842E-842ME System Reference-SYS-CP842-10E - 第90页

Machine System >> Editing Production Pr ograms On the Machine 4-54 SYS-CP842-1.0E Sequence Search Screen The sequence for which a simulation or test place ment is desired is selected on this screen. Screen Button E…

Machine System >> Editing Production Programs On the Machine

SYS-CP842-1.0E 4-53

Display Item Explanations

1. [Sequence] Displays the sequence progression status as a bar graph which indi-

cates the percentage (%).

2. [Sequence No.] Displays the sequence number for which image acquisition (by

mark camera) is occurring.

3. [Device No.] Displays the stage number, group number, slot number, and sub-

slot number of the device for the displayed [Sequence No.] (see item

2 above).

Operation Explanation

1 Start

•The START button lamp blinks except at the times shown below. Test place-

ment begins when the blinking START button is pressed.

(1) When at the sequence screen.

(2) When editing data (a ten-key pad or an input dialog box displays).

•Screen buttons are disabled during a test placement.

•If no nozzle origin position search or part discard operation has occurred since

the power was turned on, a nozzle origin position search is first performed

when the START button is pressed, followed by the test placement.

2 Continuous operation

•Intervals are inserted between each sequence.

•Operation continues until all sequences in the production program are com-

pleted. If the CYCLE STOP button is pressed while operation is in

progress, a stop does not occur until the current sequence is completed.

3 Step operation

•If started when there is no panel present, a panel is loaded, a part is placed, an

image of the placed part position is acquired by the mark camera and dis-

played on the monitor. Operation then stops.

4 Specifying the initial sequence

•The initial sequence can be specified if a panel has been loaded to the main

conveyor but test placement is not occurring.

5 Panel unloading

•A panel is not unloaded after production is completed. The [Unload] button

must be pressed to unload the panel.

•A completed panel which is on the main conveyor is automatically unloaded if

the START button is pressed.

•To perform another test placement after a test placement and simulation have

been completed, press the [Unload] button to unload the panel, then per-

form another test placement.

6 Saving the production program

•When the [Close] button is clicked after editing a production program, a dialog

box displays inquiring if the production program is to be saved. If saved,

production program overwriting occurs. If not saved, the edited content is

abandoned.

Machine System >> Editing Production Programs On the Machine

4-54

SYS-CP842-1.0E

Sequence Search Screen

The sequence for which a simulation or test placement is desired is selected on this

screen.

Screen Button Explanations

A. [Sequence No.]: Displays a ten-key pad where the desired sequence number

(search object) can be entered.

B. [Reference Designator Search]: Displays a ten-key pad where the desired reference

designator (search object) can be entered.

C. [ZOOM+]: Zooms in and enables image scrolling, and sequence cursor

movement.

D. [Close]: Returns to either the simulation or the test placement screen

(returns to the screen from which this screen was accessed).

Display Item Explanations

1. [Monitoring Preview] Displays the panel position of the sequence number indicated

by the [Sequence No.] item (item A. above).

Specify the sequence number.

FUJI

ErrorOperator

JOG:X Y CAM

Servo CountGEMCCD Monitor

Sequence SearchFUJI_CP7_2001

Front

123

Sequence Number

ZOOM +

ZOOM -

Move Cursor

Reference

Designation Search

MIN

Set Switch

CP7S2010E

Machine System >> Editing Production Programs On the Machine

SYS-CP842-1.0E 4-55

Specifying A Sequence

A sequence can be specified in the following 3 ways.

1 By entering the sequence number directly.

A. Click the [Sequence No.] button to display a ten-key pad, then enter the

desired sequence number. If the modeling object is enabled, the part for

the specified sequence displays on the modeling object.

2 By entering a reference designator.

B. Click the [Reference Designator] button to display a ten-key pad, then

enter the search object reference designator. If the modeling object is

enabled, the part for the specified sequence displays on the modeling

object.

3 By moving the cursor to the desired position on the modeling object.

C. Click the [ZOOM+] button to enable the modeling object. The procedure

for specifying a sequence using the modeling object is explained on the fol-

lowing page (Sequence Search 2 Screen).