SOM-2080-001_w.pdf - 第147页
144 SOM-2080 Erroe ID Error Name, Description, Cause, and Remedy 60200c Auto. Teaching Mode in Auto.Opn An error occurred during teaching. (Front) (Operation timeout in the Head Rotation Center Offset Teaching) ----- 602…
143
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
601f09 NL Axis offset teach
An error occurred in the teaching operation.
-----
602001 Auto. Teaching Mode in Auto.Opn
A recog error occurred during teaching operation.(Back) (This problem may be
caused by the teaching jig unset or dirty.)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602002 Auto. Teaching Mode in Auto.Opn
A recog error occurred during teaching operation.(Front) (This problem may be
caused by the teaching jig unset or dirty.)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602003 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear)
-----
602004 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front)
-----
602005 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred during teaching. (Rear)
-----
602006 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred during teaching. (Front)
-----
602007 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation timeout in the Beam Offset
Teaching)
-----
602008 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation timeout in the Beam Offset
Teaching)
-----
602009 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation error in the Beam Offset
Teaching)
-----
60200a Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation error in the Beam Offset
Teaching)
-----
60200b Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation timeout in the Head Rotation
Center Offset Teaching)
-----
6.14 Automatic Teaching
1005-001
144
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
60200c Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation timeout in the Head
Rotation Center Offset Teaching)
-----
60200d Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation error in the Head Rotation
Center Offset Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
60200e Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation error in the Head Rotation
Center Offset Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
60200f Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation timeout in the Fiducial Mark
Position Teaching)
-----
602010 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation timeout in the Fiducial Mark
Position Teaching)
-----
602011 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Rear) (Operation error in the Fiducial Mark
Position Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602012 Auto. Teaching Mode in Auto.Opn
An error occurred during teaching. (Front) (Operation error in the Fiducial Mark
Position Teaching)
Check that the teaching jig is set properly on the position, or clean the teaching
jig.
602013 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred in the nozzle change. (Rear)
-----
602014 Auto. Teaching Mode in Auto.Opn
An error for timeout occurred in the nozzle change. (Front)
-----
602015 Auto. Teaching Mode in Auto.Opn
An error occurred in the nozzle change. (Rear)
-----
602016 Auto. Teaching Mode in Auto.Opn
An error occurred in the nozzle change. (Front)
-----
6.14 Automatic Teaching
1005-001
145
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
602017 Auto. Teaching Mode in Auto.Opn
The offset value exceeded the tolerance at the beam offset teaching.(rear)
Open the "MAINT"/ "TEACHING" tab sheet and perform the "P.E..C. Recog.
Camera & Beam Offset".
602018 Auto. Teaching Mode in Auto.Opn
The offset value exceeded the tolerance at the beam offset teaching.(front)
Open the "MAINT"/ "TEACHING" tab sheet and perform the "P.E..C. Recog.
Camera & Beam Offset".
602019 Auto. Teaching Mode in Auto.Opn
The offset value exceeded the tolerance at the head center offset teaching.(rear)
Open the "MAINT"/ "TEACHING" tab sheet and perform the "Head Center Offset
Teaching".
60201a Auto. Teaching Mode in Auto.Opn
The offset value exceeded the tolerance at the head center offset teaching.(front)
Open the "MAINT"/ "TEACHING" tab sheet and perform the "Head Center Offset
Teaching".
60201b Auto. Teaching Mode in Auto.Opn
The offset value exceeded the tolerance at the basis mark position teaching.(rear)
Open the "MAINT"/ "TEACHING" tab sheet and perform the "Basis Mark Position
Teaching".
60201c Auto. Teaching Mode in Auto.Opn
The offset value exceeded the tolerance at the basis mark position teaching.(front)
Open the "MAINT"/ "TEACHING" tab sheet and perform the "Basis Mark Position
Teaching".
602101 Beam correct offset teach.
Mark can not be recognized on the glass Jig PCB.
Check the PCB position.
602102 Beam correct offset teach.
An error occurred on teaching operation.
Check the Rcg Communicatin or beam activity.
6.14 Automatic Teaching
1005-001