SOM-2080-001_w.pdf - 第153页
150 SOM-2080 Erroe ID Error Name, Description, Cause, and Remedy 6b30a1 V.Bend Detection Error 2pinTr Error! (PIN1 upper) Check for any bent terminals (vertically bent leads). 6b30b1 V.Bend Detection Error 2pinTr Error! …
149
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
6b2041 V.Bend Detection Operation Error
Measurement Start Signal Not Recognized. (2040)
Check the coupling cable between the V-bend unit PC and the main machine.
(Measurement Start Signal)
6b2051 V.Bend Detection Operation Error
Illegal Command Parameter. (2050)
Shut down the machine and power it up again.
6b2061 V.Bend Detection Operation Error
Unknown Reference Component Data. (2060)
Shut down the machine and power it up again.
6b2071 V.Bend Detection Operation Error
Improper Measurement Mode. (2070)
Make the measurement in the high accuracy mode.
6b3001 V.Bend Detection Error
Coplanarity Error! (3000)
Check for any bent terminals (vertically bent balls and leads).
6b3011 V.Bend Detection Error
Terminal Misregistration Error! (3010)
Check for the position and pitches of the terminals (balls and leads).
6b3021 V.Bend Detection Error
Terminal Detection Error! Wrong Measurement Data (Completely Dark Image).
(3020)
Check the component size and thickness data.
6b3031 V.Bend Detection Error
Terminal Detection Error! Error in Number of Extracted Terminals (labeling).
(3030)
Check the size and pickup position of the component.
6b3041 V.Bend Detection Error
Terminal Detection Error! Terminal Allocation Error (Impossible Terminal
Arrangement Detection). (3040)
Check the component size and thickness data.
6b3061 V.Bend Detection Error
Terminal Detection Error! Edge Detection Error (Impossible Edge Detection of
Gauge during Installation Calibration). (3060)
Check the pickup condition of the calibration gauge and the intallation of the unit.
6b3071 V.Bend Detection Error
Coplanarity Error! (3070)
-----
6b3081 V.Bend Detection Error
Impaired Terminal (Nicked) Error. (3080)
Check the position of the leads or the balls and the quantity data.
6b3091 V.Bend Detection Error
2pinTr Error! (ONE all NG)
Check the component size and thickness data.
6.16 V.Bend Detection System Error
1005-001
150
SOM-2080
Erroe ID Error Name, Description, Cause, and Remedy
6b30a1 V.Bend Detection Error
2pinTr Error! (PIN1 upper)
Check for any bent terminals (vertically bent leads).
6b30b1 V.Bend Detection Error
2pinTr Error! (PIN1 lower)
Check for any bent terminals (vertically bent leads).
6b30c1 V.Bend Detection Error
2pinTr Error! (PIN2 upper)
Check for any bent terminals (vertically bent leads).
6b30d1 V.Bend Detection Error
2pinTr Error! (PIN2 lower)
Check for any bent terminals (vertically bent leads).
6b3101 V.Bend Detection Error
Reference Plane Flapping Error. (3100)
Check the pickup surface and condition of the component.
6b3111 V.Bend Detection Error
Terminal Detection Error! Out of Edge Position Measurable Range ("Near" Side).
(3110)
Check the component thickness and V-bend unit height offset data.
6b3121 V.Bend Detection Error
Terminal Detection Error! Out of Edge Position Measurable Range ("Far" Side).
(3120)
Check the component thickness and V-bend unit height offset data.
6b3131 V.Bend Detection Error
Sampling Error ("DARK" Alarm). (3130)
Decrease the dark level (dlv) of the component library data.
6b3141 V.Bend Detection Error
Sampling Error ("BRIGHT" Alarm). (3140)
Decrease the laser power (lpw) of the component library data.
6b9001 V.Bend Detection System Error
Sysyem error. (9000)
Shut down the machine and power it up again.
6b9011 V.Bend Detection System Error
-----
6.16 V.Bend Detection System Error
1005-001
151
SOM-2080
6.17 Barcode Detection
1005-001
6.17 Barcode Detection
Table 19
Erroe ID Error Name, Description, Cause, and Remedy
700101 Barcode Detection
The bar code data is not read.
-----
700102 Barcode Detection
The pattern program is not found.
-----
700103 Barcode Detection
Error in pattern program.
-----
700104 Barcode Detection
Overtime error in reading of bar code label.
-----
700105 Barcode Detection
Error in pattern program now editing.
-----
700106 Barcode Detection
Error in pattern program data transfer.
-----
700107 Barcode Detection
Data is used temporarily now.
-----
700108 Barcode Detection
Please Set-up.
-----
700109 Barcode Detection
Cannot start by Machine is not in "STOP" or "WAIT" mode.
-----
700110 Barcode Detection
The PCB was not available Barcode ID.
-----
700111 Barcode Detection
Program -change was not able to executed.
-----
700112 Barcode Detection
Application error.
-----
700113 Barcode Detection
The nozzle set-up was not able to begin.
-----
700114 Barcode Detection
The product.operation was not able to begin.
-----