X-Series-Maintenance-Manual(1) - 第39页
Minor Maintenance Performing Maintenance Tasks Maintenance Tasks for the Component Feed Device Maintenance Manual SIPLACE X Series 39 Removing an d Preserving th e Magnetic Stri p on the Com ponent Tro ll ey for S Feeder…
Minor Maintenance
Maintenance Tasks for the Component Feed Device Performing Maintenance Tasks
38 Maintenance Manual SIPLACE X Series
Greasing the Centering St rip on the Component Trolley for X Feeder Modules
4.3.3.2 Greasing the Centering Strip on the Component Trolley for X Feeder Modules
Greasing the Plunger Pins on the Component Trolley for S Feeder Modules
4.3.3.3 Greasing the Plunger Pins on the Component Trolley for S Feeder Modules
► Spray the centering strip (1) with a thin film of "Oil
spray Surface Shield" [00328575-xx]. Pay close
attention to the holes in the centering strip.
► Then wipe the centering strip with a lint-free cloth.
► Repeat these steps at all component trolleys.
NOTICE
Undocking many times
► Perform this task if the component trolley is undocked on a frequent basis.
► Dock out the component trolley.
► Greas the plunger pins (1) of the change over table
insert with a brush and UNISILKON L250L.
► Grease the plunger pins (2) of the ODU connector on
the component trolley docking unit with a brush and
UNISILKON L250L.
► Dock in the component trolley once more.
Minor Maintenance
Performing Maintenance Tasks Maintenance Tasks for the Component Feed Device
Maintenance Manual SIPLACE X Series 39
Removing an d Preserving th e Magnetic Stri p on the Com ponent Troll ey for S Feeder Mo dules
4.3.3.4 Removing and Preserving the Magnetic Strip on the Component Trolley for S Feeder Modules
► Return the feeders to the feeder area.
► Clear the feeder area.
► Remove any loose components from the component
feeder table using the vacuum cleaner.
► (1) Use a whetstone to remove any bumps on the
magnetic rail.
► (2) Preserve the feeder area using a lint-free cloth
sprayed with WD40.
► Vacuum up any loose components from the tape
container and remove any unwanted stickers and
adhesive tape.
NOTICE
Pay attention to location and connection
► Make sure that each feeder is in the correct location and is connected properly.
Minor Maintenance
Maintenance Tasks for the Conveyor Consumables, Spare and Wear Parts, Tools
40 Maintenance Manual SIPLACE X Series
Maintenance Tasks for the Conveyor
4.4 Maintenance Tasks for the Conveyor
Consumables, Spare and Wear Parts, Tools
4.4.1 Consumables, Spare and Wear Parts, Tools
▪ Interflon Fin Super (Teflon oil) [03017760-xx]
▪ Lint-free cloths [03082092-xx]
▪ Ethanol
▪ SIPLACE cleansing tissue [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Set of Phillips screwdrivers
▪ ESD wristband [00320279-xx]
▪ Vacuum cleaner
Preparatory Steps
4.4.2 Preparatory Steps
► There must be no PCBs in the machine during the following maintenance steps.
► Make a note of the current conveyor width.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
Performing Maintenance Tasks
4.4.3 Performing Maintenance Tasks
Vacuuming the Conveyors, Conveyor Belts, Sensors and Lifting Table
4.4.3.1 Vacuuming the Conveyors, Conveyor Belts, Sensors and Lifting Table
CAUTION
Loose components
Loose components on the PCB conveyor could cause faults.
► Use the vacuum cleaner to remove all loose
components on and around the PCB conveyor. Pay
particular attention to the areas near the lifting table,
the width adjustment, the trailing cables and the
conveyor belts.