X-Series-Maintenance-Manual(1) - 第42页
Minor Maintenance Maintenance Tasks for the Conveyor Final Work 42 Maintenance Manual SIPLACE X Series Cleaning and Preserving t he Guide Shafts of the Wid th Adjustmen t 4.4.3.5 Cleaning and Preserving the Guide Shafts …
Minor Maintenance
Performing Maintenance Tasks Maintenance Tasks for the Conveyor
Maintenance Manual SIPLACE X Series 41
Cleaning and Preserving t he Hexagonal Sha fts
4.4.3.2 Cleaning and Preserving the Hexagonal Shafts
Cleaning the Fixtu re Tape
4.4.3.3 Cleaning the Fixture Tape
Cleaning and Preserving t he Recirculatin g Ball Screws of the Width Adjustment
4.4.3.4 Cleaning and Preserving the Recirculating Ball Screws of the Width Adjustment
► Apply Teflon oil to a lint-free cloth and clean the
hexagonal shafts (1) in the conveyor.
Alternatively you can also use a SIPLACE cleansing
tissue.
► Repeat the procedure for all hexagonal shafts in the
conveyor.
CAUTION! Risk of cutting!
The fixing strip has a sharp edge.
► Clean the fixing strip of the width adjustment
clamping unit using a lint-free cloth moistened with
ethanol.
► Clean and preserve the recirculating ball screw (1) by
running a SIPLACE cleansing tissue along the thread
of the screw.
► Repeat this procedure for all recirculating ball
spindles on the conveyor.
Minor Maintenance
Maintenance Tasks for the Conveyor Final Work
42 Maintenance Manual SIPLACE X Series
Cleaning and Preserving t he Guide Shafts of the Wid th Adjustment
4.4.3.5 Cleaning and Preserving the Guide Shafts of the Width Adjustment
Cleaning and Pre serving t he Guide Shaft of the Conv eyor Sides
4.4.3.6 Cleaning and Preserving the Guide Shaft of the Conveyor Sides
Final Work
4.4.4 Final Work
► Reconnect all clamps, where applicable.
► Set back to the original conveyor width.
► Apply Teflon oil to a lint-free cloth and clean the
bottom (1) and top (2) guide shaft of the width
adjustment.
Alternatively you can also use a SIPLACE cleansing
tissue.
► Repeat the procedure for all width adjustment guide
shafts on the conveyor.
► Clean and preserve the guide shaft (1) for the
conveyor sides with a SIPLACE cleansing tissue.
► Repeat the procedure for all guide shafts on the
conveyor sides.
Minor Maintenance
Consumables, Spare and Wear Parts, Tools Maintenance Work on the Gantry
Maintenance Manual SIPLACE X Series 43
Maintenanc e Work on the Gantry
4.5 Maintenance Work on the Gantry
Consumables, Spare and Wear Parts, Tools
4.5.1 Consumables, Spare and Wear Parts, Tools
▪ Lint-free cloths [03082092-xx]
▪ Ethanol
▪ Protective latex gloves [00372972-xx]
▪ ESD wristband [00320279-xx]
▪ SIPLACE cleansing tissue [00315253-xx]
Preparatory Steps
4.5.2 Preparatory Steps
► There must be no PCBs in the machine during the following maintenance steps.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
Performing Maintenance Tasks
4.5.3 Performing Maintenance Tasks
See also
1.1.2 Safety Instructions for Working with Strong Magnetic Fields [ ➙ 8]
Cleaning the X Ax is Scale
4.5.3.1 Cleaning the X Axis Scale
CAUTION! Always use soft cloths and minimal
pressure to clean the scales.
Dirty scales can lead to counting errors and, as a
consequence, to machine stoppages.
► Clean the incremental scales (1) of the X axes with a
lint-free cloth soaked in ethanol.