X-Series-Maintenance-Manual(1) - 第61页
Minor Maintenance Performing Maintenance Tasks Maintenance Tasks for C&P6/12 Head Maintenance Manual SIPLACE X Series 61 ► Wear l aboratory gloves for this step. ► (1) Check the suction plat e for damage. If it is da…
Minor Maintenance
Maintenance Tasks for C&P6/12 Head Performing Maintenance Tasks
60 Maintenance Manual SIPLACE X Series
► (1) Spray a little Teflon grease into a suitable vessel.
► (2) Moisten the cottonwool bud with Teflon grease.
CAUTION! Do not spray Teflon grease directly
onto the cottonwool buds with the spray can. Using a
separate vessel helps to avoid excess application and
consequential damage to the placement head!
Always use ethanol for cleaning. Do not use white spirit,
otherwise streaks will form on the incremental disk!
Do not use silicon-soluble cleaning agents.
► (3) Run the dampened cottonwool bud along the
groove of the anti-rotation element.
► (1) Check that the switching ring moves easily in the
sleeve. The unit that is moved as a result must not
stick or grate. However, if still does stick or grate,
despite greasing, send the sleeve to the SIPLACE
Sleeve Maintenance team.
► Repeat these steps for all sleeves.
► Remove the dirt from the longitudinal vacuum hole by
turning the 1.4 mm drill bit clockwise in the hole.
Turning the bit will remove the dirt from the hole.
► Use the same procedure to remove the dirt from the
transverse vacuum hole using the 1.1 mm drill bit.
Minor Maintenance
Performing Maintenance Tasks Maintenance Tasks for C&P6/12 Head
Maintenance Manual SIPLACE X Series 61
► Wear laboratory gloves for this step.
► (1) Check the suction plate for damage. If it is
damaged, replace it.
► (2) Clean the sleeve suction plate using a dry, lint-
free cloth.
► Clean the edge (1) of the sleeve with a lint-free cloth,
moistened with ethanol.
► Clean the incremental disk (2) of the sleeve with a
lint-free cloth, moistened with ethanol.
► Clean the sleeve shaft (1) with a lint-free cloth,
moistened with ethanol.
► Carefully clean the circumference (2) of the ball catch
with a cottonwool bud moistened with ethanol.
Minor Maintenance
Maintenance Tasks for TwinHead Consumables, Spare and Wear Parts, Tools
62 Maintenance Manual SIPLACE X Series
Maintenance Tasks for TwinHead
4.9 Maintenance Tasks for TwinHead
Consumables, Spare and Wear Parts, Tools
4.9.1 Consumables, Spare and Wear Parts, Tools
▪ Interflon Fin Super (Teflon oil) [03017760-xx]
▪ Lint-free cloths [03082092-xx]
▪ Replacement filter FE 50 [03047489-xx]
▪ ESD wristband [00320279-xx]
▪ Long-nosed pliers
Preparatory Steps
4.9.2 Preparatory Steps
► Switch off the machine and secure it to prevent unauthorized reactivation. Observe the instructions
in section "1.2 Preparatory Work..." [ ➙ 11].
► Set the nozzles down in the nozzle changer.
Performing Maintenance Tasks
4.9.3 Performing Maintenance Tasks
Cleaning the Sleeve and Nozzle Sea t
4.9.3.1 Cleaning the Sleeve and Nozzle Seat
Cleaning /Replacin g the Additional V olume Fi lter
4.9.3.2 Cleaning/Replacing the Additional Volume Filter
► Spray a small amount of Teflon oil on a lint-free cloth
and clean the sleeve and nozzle seat.
Alternatively you can also use a SIPLACE cleansing
tissue.
► Carefully blow through the nozzle.
► Repeat these steps on the second TwinHead
module.
► Unscrew the filter (1).
NOTICE! If the filter is difficult to access, use the
long-nosed pliers to help you. You do not need to remove
the head.
► Clean the filter by carefully blowing compressed air
through it.
► Check the filter for damage.
► If it is damaged replace it with a new one.
► Screw the filter tight again.
► Repeat these steps on the second TwinHead
module.