X-Series-Maintenance-Manual(1) - 第70页
Major Maintenance Maintenance Tasks for the Com ponen t Docking Unit Consumables, Sp are and Wear Parts, Tools 70 Maintenance Manual SIPLACE X Series Maintenance Tasks for the Compon ent Docking Unit 5.3 Maintenance Task…
Major Maintenance
Performing Maintenance Tasks Maintenance Tasks for Base Machine
Maintenance Manual SIPLACE X Series 69
EMERGENCY STOP button
► Check the EMERGENCY STOP buttons for damage.
► Check that the control system switches off
immediately when you actuate the button. If this is not
the case, contact your SIPLACE Service team.
► Repeat this procedure for all emergency stop
buttons.
Major Maintenance
Maintenance Tasks for the Component Docking Unit Consumables, Spare and Wear Parts, Tools
70 Maintenance Manual SIPLACE X Series
Maintenance Tasks for the Component Docking Unit
5.3 Maintenance Tasks for the Component Docking Unit
Consumables, Spare and Wear Parts, Tools
5.3.1 Consumables, Spare and Wear Parts, Tools
▪ Sheet of DIN A3 paper (or 2x A4)
▪ Adhesive tape
▪ Scissors
▪ ESD wristband [00320279-xx]
Preparatory Steps
5.3.2 Preparatory Steps
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
Performing Maintenance Tasks
5.3.3 Performing Maintenance Tasks
Functio n Test of Used Tape Cutter
5.3.3.1 Function Test of Used Tape Cutter
CAUTION
Risk of cutting
Observe the safety instructions for the cutter!
► "1.1.5 Safety Instructions for Work on the Cutting Device" [ ➙ 9]
► Insert a sheet of DIN A3 paper or two DIN A4 sheets
attached to one another into the empty tape duct.
NOTICE! A DIN A4 sheet on its own is too short
to reach the tape cutter.
► Attach the sheet of paper with adhesive tape to the
empty tape duct.
Make sure that there is no paper protruding upwards
in the placement head travel range.
► Start the cutting process in the software
► Take the sheet of paper out of the empty tape duct
again.
If it has not been cut through accurately, replace the
cutting blades. Please contact your SIEMENS
Service team for this work.
Major Maintenance
Consumables, Spare and Wear Parts, Tools Maintenance Work on the Gantry
Maintenance Manual SIPLACE X Series 71
Maintenanc e Work on the Gantry
5.4 Maintenance Work on the Gantry
Consumables, Spare and Wear Parts, Tools
5.4.1 Consumables, Spare and Wear Parts, Tools
▪ Lint-free cloths [03082092-xx]
▪ SIPLACE cleansing tissue [00315253-xx]
▪ Klüberplex BEM 34-132 lubricant, 1 kg tin [00374565-xx]
▪ Protective latex gloves [00372972-xx]
▪ Cotton gloves [00359087-xx]
▪ ESD wristband [00320279-xx]
▪ Grease gun with hose for Y axis (volume applied: approx. 0.4 g) [00374563-xx]
▪ Grease gun with nozzle for X axis (volume applied: approx. 0.13 g) [00374564
-
xx]
▪ DIN71412 - A M6 lubrication nipple [03036936-xx], if required
▪ Cooling air set (black) [03003704-xx] or cooling air set (white) [03030955-xx], if required
▪ Set of Allen wrenches
▪ A high-precision set of scales (recommended minimum measuring accuracy: 1 g)
Preparatory Steps
5.4.2 Preparatory Steps
► There must be no PCBs on the PCB conveyor for the following jobs.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 11].
► Prepare the grease gun.