X-Series-Maintenance-Manual(1) - 第73页
Major Maintenance Performing Maintenance Tasks Maintenance Work on the Gantry Maintenance Manual SIPLACE X Series 73 Performing Maintenan ce Tasks 5.4.3 Performing Maintenance Tasks See also 1.1.2 Safet y Instructio ns…
Major Maintenance
Maintenance Work on the Gantry Preparatory Steps
72 Maintenance Manual SIPLACE X Series
Filling the Grease Gun
5.4.2.1 Filling the Grease Gun
► Pull back the grease gun plunger. It must lock into
place.
► Open the grease gun by unscrewing the top section.
► Fill the grease gun with suitable grease. Use a clean
spatula.
Try to fill the gun with grease without trapping in any
air pockets.
► Close the grease gun by screwing the top section
back on.
► Loosen the lock on the back of the grease gun. The
spring force moves the plunger forward.
► Push back the ball on the vent screw to vent the
grease gun. Use a screwdriver or similar tool to help
you.
CAUTION! Always vent the grease gun once
you have finished greasing the machine!
► Press the trigger until the grease emerges from the
front of the gun.
► Remove excess grease with a lint-free cloth.
The grease gun is now ready for use.
Major Maintenance
Performing Maintenance Tasks Maintenance Work on the Gantry
Maintenance Manual SIPLACE X Series 73
Performing Maintenance Tasks
5.4.3 Performing Maintenance Tasks
See also
1.1.2 Safety Instructions for Working with Strong Magnetic Fields [ ➙ 8]
Greasing and Cleaning the X A xis
5.4.3.1 Greasing and Cleaning the X Axis
► Check the amount of grease with the help of the scales. Adjust the amount of grease if necessary.
When using the "grease gun with nozzle for the X axis (dosage approx. 0,13 g)" [00374564-xx], the
amount of grease can be changed with a setting screw on the handle.
CAUTION
Greas all grease nipples and pay attention to the capacity!
► Remember to grease every visible grease nipple on the X and Y axes!
► Use the amounts of grease specified. Too much or too little grease can damage the
bearing.
► Fill the "X axis with travel limitation" grease gun with
Klüberplex BEM 34-132.
► Set the grease gun to a dosage of 0.13 g, by
adjusting the screw (1) to 29 mm.
NOTICE
Checking the amount of grease
Depending on the accuracy of your scales, you might need to do 10 or 100 strokes, for example,
to check the amount of grease. Select the number of strokes accordingly to ensure adequate
accuracy. (e.g. for a pair of scales with a measuring accuracy of 1 g: 100 strokes --> 13 g)
Major Maintenance
Maintenance Work on the Gantry Performing Maintenance Tasks
74 Maintenance Manual SIPLACE X Series
► Position the hose of the grease gun straight onto the
lubrication nipple (1).
► Apply one squeeze of the grease gun (approx. 0.13
cm
3
per squeeze).
► If the grease emerges from the grease nipple, then
either the bearing is already full or the grease nipple
is not sealed correctly. In the latter case, use a new
grease nipple.
► Move the X-axis head plate approx. 30 cm. This
distributes the grease.
► Repeat the pressing and moving process two more
times. The correct amount of grease has then been
applied.
The total amount of grease (3 x 0.13 cm
3
[g] in all
bearings!
► Use a lint-free cloth to remove any excess grease
from on and around the grease nipple.
► Repeat these steps for the other lubrication nipples
(2) of the X axis. (4 per gantry)
► Repeat these steps for all gantries.