00192231-09_VD_SSW 407.05_de en - 第22页

Software Version Description, Station Software Version 407.05 07/2008 Edition 5.5.2.6 Entering component level Changing the component level is only possible on the "Oper ator" access level. This does not apply …

Software Version Description, Station Software Version 407.05 07/2008 Edition

5.5.2.3 Support for the track status on the SMV screen

Tracks which have been verified positively during component verification are indicated by a green "9" on the

SMV screen. Previously, this icon was also displayed if the corresponding track has been deactivated as a

result of a detected splice. In future, tracks which are verified positively but deactivated on the station will be

indicated by "(9)".

5.5.2.4 Batch status function in the GUI

The component level indicator has a new column "Status" to display the data recording status of the track

with respect to Traceability.

Only tracks subject to component verification are supported.

Contents of the "Status" column:

<empty> means: no batch data available

means: 1 verified batch

X means: 1 verified batch, track deactivated because follow-on batch is missing (e.g. after

detected splice)

means: 2 verified batches

means: 2 verified batches, transitional area, both batches are logged

The content of the batch data, i.e. the recorded barcodes are not shown.

5.5.2.5 Sort sequence the component level indicator

Clicking on the "Location" column now sorts as follows:

- Sort by location

- within the location by track number

- then by division number

If the component level indicator is opened again, the sort sequence selected previously is still active. (This

does not apply after a reboot).

21 of 104

Software Version Description, Station Software Version 407.05 07/2008 Edition

5.5.2.6 Entering component level

Changing the component level is only possible on the "Operator" access level. This does not apply to any of

the other entries (e.g. threshold).

Specifying the remaining length of the tape behind the feeder

It is difficult to estimate the filling level of a partially used reel. The system therefore now provides help for

doing this. The operator specifies the remaining length of the tape behind the rear edge of the feeder.

The system first calculates the overall remaining tape length including the length of the feeder. On the basis

of the feeder pitch (which must be entered in the programming system) the system calculates the number of

components remaining.

Remaining component level = (length of feeder + remaining length behind feeder) / pitch

The length of the feeder can be assumed to be 50 cm.

Next to the screen area "Supply", there is another screen area "Remaining length", which includes this entry

field.

An entry in one of the fields "Supply" or "Remaining length" always causes the value in the other field to be

adjusted.

If the component level correction function is called by clicking the "Edit" button in the component level

indicator, the input focus is on the "Enter remaining length" field. The value previously entered in the field is

also selected, so that the operator can correct the value using only the keyboard without needing the mouse.

Note:

The

threshold value "Remaining length" is also calculated as of the rear edge of the feeder as of this version.

If a remaining length x is entered, the system uses a remaining length of x + 50 cm. This harmonizes the

specification with the new option for entering the component levels.

5.5.2.7 Initialization using the menu command "New table"

The function "New table" ("Set") should always reset the data maintenance for the corresponding track. All

data scanned in previously and all saved commands (splice detected) are deleted. The record reported with

"New table" is entered in the first batch. This option allows the operator to proceed in a defined manner from

"unclear" statuses. In the case of "repair operations" (continuation from a situation which is unclear for the

operator), the operator is responsible for recording the correct status:

22 of 104

Software Version Description, Station Software Version 407.05 07/2008 Edition

"Repair" of a batch which has been started:

Re-enter the data with "New Table" + manual correction of component level

"Repair" of a spliced reel, splice still before the sensor:

Re-enter the data of the old batch with "New Table" + refill the new batch + manual correction of component

level

"Repair" of a spliced reel, splice still before the sensor:

Step forward to the new batch, re-enter next batch with "New table"

"Repair" of a spliced reel, splice after the sensor:

Step forward to the new batch, re-enter next batch with "New table"

5.5.2.8 Setup names of up to 50 characters

In conjunction with SMV Version 6.6.34 (or later) it is possible to use setup names of up to 50 characters

(was previously 20 characters).

5.5.3 2321m embedded software for ICOS MVS 340

As of version 407.04, the embedded software 2321m is used by default on machine types SIPLACE F

SIPLACE S23 and SIPLACE F5HM. This version is required as a result of the revised hardware (MVS 340

Rev. 6). Downloading an older version of the embedded software onto this hardware would render it

unusable. All older releases of the MVS 340 can be operated with the new embedded software.

23 of 104