CM88Maintenace2x.PDF - 第112页

Page 1-20 3Y3C-E-MMZ0A-A01-00 Pickup Position Calibration 4 . Press UNLOCK + START . • The calibration starts. • After the calibration is completed, the message appears. 3. Removing the Jigs 1 . T urn OFF the servo switc…

100%1 / 114
Page 1-19
CALIBRATION
3Y3C-E-MMZ0A-A01-00
Pickup Position Calibration
2. Calibration
1. Press
UNLOCK
+ Teach start .
• The confirmation message appears.
2. After confirmation, press Yes .
• The confirmation message appears.
3. After confirmation, press Yes .
To the next page
Page 1-20
3Y3C-E-MMZ0A-A01-00
Pickup Position Calibration
4. Press
UNLOCK
+
START
.
• The calibration starts.
• After the calibration is completed, the message
appears.
3. Removing the Jigs
1. Turn OFF the servo switch.
2. Open the rear center safety cover.
3.
Remove the jigs by performing the
procedure opposite to the setting one.
1. Turn OFF the power switches of the CCU and
the power supply box.
2. Remove the power supply cord, then remove
the other cables.
∗ When setting and removing the camera jig, be
careful that the jig does not interfere with the
nozzles on the head.
4. Return the wiring to what it was.
Message
3Y3C-AI01
OFF ( )
ON ( )
SERVO
tinU
dnakcehcrofstraP
noitacirbul
noitacirbuldnakcehC
rodradnatS
liodeificeps
doireP
-refeR
ecne
1 2 3 4 5 6 7 8 9 01 11 21 31 41 51 61 71 81 91 02 12 22 32 42 52 62 72 82 92 03 13
tinuRM
eguagerusserPerusserpriakcehCaPM87.0otaPM94.0)M1(h0655-5-1
reviecerretaWreviecerretawytpmednakcehC
reviecerehtytpmE
llufflahstegtierofeb
)M1(h0655-5-1
elbatY-X
tinuelohW
nI(esionegnartsrofkcehC
gninnurdnanoitarepognitrats
)enihcam
esionoN)D1(h422-3-1
naelC–)M1(h0654-5-1
gniraebraeniLesaergylppA2AINABLA)M1(h0654-5-1
wercsllaBesaergylppA2AINABLA)M1(h0654-5-1
tinuriA
ksidsixaniaMesaergylppA2UTNAILAV)M1(h0651-5-1
gnirpSesaergylppA2UTNAILAV)M1(h0651-5-1
tinugnittuC
tinudnuorA)noitareporetfa(naelC–)D1(h426-3-1
murclufreveLetacirbuL2UTNAILAV)M2(h00017-6-1
dnedoResaergylppA2UTNAILAV)M2(h00017-6-1
edalbelbavoM
esaergylppA2UTNAILAV)M2(h00017-6-1
egnahC2UTNAILAV)M3(h00511-7-1
1xobmaC
rewollofmaCetacirbuL2UTNAILAV)M2(h00012-6-1
murclufreveLetacirbuL2UTNAILAV)M2(h00012-6-1
gnirpSesaergylppA2UTNAILAV)M2(h00012-6-1
ecafmaCesaergylppA2UTNAILAV)M2(h00012-6-1
2xobmaC
murclufreveLetacirbuL2UTNAILAV)M2(h00013-6-1
gnirpSesaergylppA2UTNAILAV)M2(h00013-6-1
ecafmaCesaergylppA2UTNAILAV)M2(h00013-6-1
3xobmaC
rewollofmaCetacirbuL2UTNAILAV)M2(h00014-6-1
murclufreveLetacirbuL2UTNAILAV)M2(h00014-6-1
gnirpSesaergylppA2UTNAILAV)M2(h00014-6-1
ecafmaCesaergylppA2UTNAILAV)M2(h00014-6-1
noitingocerpihC
noitingocerpihcfoecafssalG
aremac
naelC–)M1(h0653-5-1
pu-ekaT
gniraebraeniLetacirbuL2UTNAILAV)M2(h00018-6-1
tfahswercSesaergylppA2UTNAILAV)M2(h00018-6-1
rewollofmaCesaergylppA2UTNAILAV)M2(h00018-6-1
dnedoResaergylppA2UTNAILAV)M2(h00018-6-1
murclufreveLetacirbuL2UTNAILAV)M2(h00018-6-1
gnirpSesaergylppA2UTNAILAV)M2(h00018-6-1
epaT
gniraebraeniLetacirbuL2UTNAILAV)M2(h00019-6-1
dnedoResaergylppA2UTNAILAV)M2(h00019-6-1
rewollofmacepaTegnahCmm2.39otmm0.39)M6(h00036-7-1
regnahcelzzoN
murclufreveLetacirbuL2UTNAILAV)M2(h000111-6-1
dnedoResaergylppA2UTNAILAV)M2(h000111-6-1
gnirpSesaergylppA2UTNAILAV)M2(h000111-6-1
warcnoisnetxeelzzoNegnahCmm5.0foecapS)M6(h00035-7-1
rosnesthgieH
gnittimethgilDELfoecafssalG
trapgniviecerdna
naelC–)M1(h06501-5-1
elbatredeeFtinuelohWnaelC–)M1(h0657-5-1
Routine Check List (1/2)
High-speed Chip Mounter CM88S-M/M1/MU, CM88C-D
Approval
Signature
Check
Year Month
[Remarks]
[Make copy and use this figure for checking.]
∗ When Result of check is failure, make
contact with ________________ at once.
Passing ..................... OK
Failure .......................NG
Applying grease ........
Result of check
• For the check of once / week, check on the th day of real running every week.
• For the check of once / month, check on the th day of real running every month.
• For the check of once / quarter, check on the th day of real running every 3 months.
• For the check of once / half a year, check on the th day of real running every 6 months.
• If the device does not run, write the mark ( ).
Cycle check
∗ Cycle for checking must be varied by the change of run time and number of production for some routine check items.
But follow to the direction by instructor.