00198829-01_SM_X-Series-S_Hxxxx_EN - 第33页
2 Basic Machine 2.7 Stationary component camera Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 33 2.7 Stationary component camera 2.7.1 Replacing the stationary component camera Fig.21: Stationary cameras SST25…
2 Basic Machine
2.6 Replacing the machine foot
32 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
2.6 Replacing the machine foot
DANGER
Heavy machine part
► The machine feet are very heavy. When screws are loosened, there is a risk that
these could fall down and crush limbs.
► When replacing the machine feet, you need to raise the machine approx. 50 cm.
► Make sure that there is nobody in the hazard area. The unintentional movement or
lowering of the machine can create a risk of crushing limbs.
CAUTION
Do not move the machine
► Make sure that the machine is not moved and that the conveyor sides are not dam-
aged.
Parts, equipment and tools
Fig.20: Machine foot [03000890-xx] and machine foot HF [03002561-xx]
●
Machine foot [03000890-xx] or
Machine foot HF [03002561-xx]
●
Instruction manual for your machine
Removal/installation
► Please read the relevant chapter of the instruction manual:
– "Presetting the height of the middle machine feet"
– "Presetting the height of the outer machine feet"
2 Basic Machine
2.7 Stationary component camera
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 33
2.7 Stationary component camera
2.7.1 Replacing the stationary component camera
Fig.21: Stationary cameras SST25(1) and SST33(2)
Read the assembly instructions for this:
●
Assembly instructions "SIPLACE X-Series S - Stationary Camera 25/33 GigE" [DE+EN:
00197710‑xx]
NOTICE
Subsequent installation or conversion of stationary cameras
Observe the following documents, where necessary:
► "Incorrectly labeled spacers for stationary cameras" [DE: TI2014-02D04] [EN:
TI2014-02E04]
During retrofitting or conversion of stationary cameras or "Smart Pin Support Q10"
magazines, pay attention to correct fitting of the spacers.
► Assembly instructions "SIPLACE X-Series S - Smart Pin Support" [DE+EN: 00197394-xx]
NOTICE
Camera adaptor
You may need to fit an IC camera adaptor assembly (see assembly instructions).
► Location 1 and 4: IC camera adaptor assembly SP4 SX4a [03099004-xx] (only for IC)
► Location 2 and 3: IC camera adaptor assembly SX4a [03099054-xx] (for IC, FC and
coplan)
Fig.22: Cables
From machine number Hxxxx, the stationary
cameras fitted will have GigE.
CAUTION!
Pay attention to the correct cabling of
the stationary cameras.
Never install a GigE camera in an
older machine (up to machine number
Gxxxx) with Hotlink interface as this
will result in destruction of the camera!
The Hotlink interface can be identified
by the orange cables.
The GigE interface can be identified by
the red cables.
.
2 Basic Machine
2.7 Stationary component camera
34 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
2.7.2 Troubleshooting for stationary cameras
Fig.23: Maintenance menu
NOTICE!
Camera Connections
The Camera Connections can be
checked in the maintenance menu.
.
Error / problem
●
Errors arise during nozzle scanning, even though the nozzle has already been checked to en-
sure that it is clean.
●
During camera verification (FCCS), it is difficult to achieve the necessary illumination.
●
Increased component rejection rate, particularly with low-contrast components.
Cause
If one or more of these errors occurs, the cause may be a dirty camera.
Solution
► Clean the stationary cameras. For further information, please read the technical information "
Cleaning SIPLACE Vision camera systems" [DE:TI2014‑10D09] [EN:TI2014‑10E09].
► Please also observe the maintenance instructions for your machine.
NOTICE
"Check camera soiling" function
In station software 712.1, a new function, "Check camera soiling" was introduced. This re-
quires additional measuring tools.
For more information, please read the following documents:
► Technical information "New functions for camera verification (FCCS_di-
gital)" [DE:TI2019‑02D06] [EN:TI2019‑02E06]
► User guide "Camera calibration FCCS digital" [DEEN:00196449‑xx]
Problem
●
Error message 37752: "The LED test of the camera illumination failed" at GigE cameras
Solution
► Please contact the SIPLACE service team for more information.
Give them the following reference number: TI2015-08V03.