00198829-01_SM_X-Series-S_Hxxxx_EN - 第359页
9 Component feeding 9.6 Smart Pin Support Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 359 Fig.514: Screws fastening the linear guide ► Remove the fourscrews (1) fastening the linear guide. ► Remove the line…
9 Component feeding
9.6 Smart Pin Support
358 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
9.6.2 Replacing the front section of the cylinder
Parts, equipment and tools
●
Front section of cylinder assembly [03090168Sxx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.511: Cylinder
1. Cylinder - front section
2. Cylinder - back section
3. Swivel head
4. Pneumatic connection to the back sec-
tion of the cylinder
5. Strain relief
Fig.512: Cylinder - front section
1. Cylinder - front section
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
► Remove the screw fastening the swivel head.
Fig.513: Screws fastening the guide
► Remove the two screws(2) fastening
the pneumatic cylinder guidance(1)
.
9 Component feeding
9.6 Smart Pin Support
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 359
Fig.514: Screws fastening the linear guide
► Remove the fourscrews(1) fastening
the linear guide.
► Remove the linear guide from the base
plate. To do this, unhook the spring
from the top of the linear guide.
Fig.515: Screws fastening the cylinder
1. Trolley on the linear guide
2. Cylinder - front section
3. Cylinder - back section
4. Linear guide
5. Fastening screw for cylinder front and
back sections on the linear guide (par-
tially concealed by the trolley)
► Remove the screws fastening the front and back sections of the cylinder.
Fig.516: Connector
► Unplug the electrical connection(1) on
the front section of the cylinder(2)
.
► Remove the front section of the cylin-
der.
Installation
Follow the removal instructions in reverse order for installation. Observe the following note:
► When you screw in the linear guide trolley, press it to the left, against the stop edge, so that it
lies flush against the base plate.
9 Component feeding
9.6 Smart Pin Support
360 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
9.6.3 Replacing the back section of the cylinder
CAUTION
Do not change!
The back section of the cylinder is preset with a cover strip take-up force of 12N+/‑2N for
the Pin Picker and may not be changed.
Parts, equipment and tools
●
Cylinder back section assembly [03089379Sxx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.517: Cylinder
1. Cylinder - front section
2. Cylinder - back section
3. Swivel head
4. Pneumatic connection to the back sec-
tion of the cylinder
5. Strain relief
Fig.518: Cylinder - back section
1. Cylinder - back section
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
► Remove the front section of the cylinder. For more information, read section 9.6.2 "Replacing
the front section of the cylinder" [}358].
► Remove the screw fastening the strain relief.
► Unplug the pneumatic connection leading to the back section of the cylinder.
► If you have not already done so, remove the two screws fastening the back section of the cyl-
inder to the linear guide and then remove the back section of the cylinder.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► When you screw in the linear guide trolley, press it to the left, against the stop edge, so that it
lies flush against the base plate.
► Make sure that the coil hose and the coiled cable do not touch when fully extended.
► Check that the sensors switch properly. The switch tag of the linear guide must have approx.
1 mm space to the trolley.