00198829-01_SM_X-Series-S_Hxxxx_EN - 第365页
9 Component feeding 9.6 Smart Pin Support Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 365 9.6.7 Replacing the pneumatic cylinder Parts, equipment and tools ● Pneumatic cylinder [03088037Sxx] ● Circlip pliers s…
9 Component feeding
9.6 Smart Pin Support
364 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
9.6.6 Replacing the swivel head
Parts, equipment and tools
●
Swivel head with inner thread KBRM-03 [03088119Sxx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.523: Swivel head
1. Swivel head
2. Pneumatic cylinder guidance
3. Pneumatic cylinder
4. Pneumatic connection for pneumatic
cylinder
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
Fig.524: Screws fastening the guide
► Remove the two screws(2) fastening
the pneumatic cylinder guidance(1)
.
► For better access, you may want to un-
plug the electrical connections to the
control board. In this case, note the
connector positions to make clear as-
signment easier later on.
► Remove the screw fastening the swivel head.
► You may find it helpful to unplug the pneumatic connection on the pneumatic cylinder so that
you can move the pneumatic cylinder more easily.
► Remove the swivel head from the pneumatic cylinder.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instructions:
► Check the linear guide travel path. The linear guide must be easy to move along the whole length.
► Check that the sensors switch properly. The switch tag of the linear guide must have approx.
1 mm space to the trolley.
9 Component feeding
9.6 Smart Pin Support
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 365
9.6.7 Replacing the pneumatic cylinder
Parts, equipment and tools
●
Pneumatic cylinder [03088037Sxx]
●
Circlip pliers size 0 (supplier: http://www.hoffmann-tools.com – item no.:719770 J0)
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.525: Pneumatic cylinder
1. Swivel head
2. Pneumatic cylinder guidance
3. Pneumatic cylinder
4. Pneumatic connection for pneumatic
cylinder
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
► Remove the swivel head. For more information, read section 9.6.6 "Replacing the swivel
head" [}364].
► Unplug the pneumatic connection to the pneumatic cylinder.
Fig.526: Holding bolt
► Remove the circlip on the holding
bolt(1)
of the pneumatic cylinder and
then pull out the holding bolt.
9 Component feeding
9.6 Smart Pin Support
366 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► The circlips on the holding bolts are highly sensitive. Take care when placing these on the
holding bolt.
► Set the swivel head so that the following conditions are fulfilled:
► Check the linear guide travel path. The linear guide must be easy to move along the whole
length.
► Check that the sensors switch properly. The switch tag of the linear guide must have approx.
1 mm space to the trolley.
See also
2 9.6.12 "Replacing the top sensor" [}371]
2 9.6.13 "Replacing the bottom sensor" [}372]
9.6.8 Replacing the coil hose
Parts, equipment and tools
●
Coil hose for solenoid valve [03090227Sxx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
NOTICE
Replacing the strain reliefs
When working with the coil hose or the coiled cable, observe the technical information
"Smart Pin Support: Replacing Faulty Coiled Cables at the Pin Picker (Update)" [DE:
TI2013-09D04] [EN: TI2013-09E04].
► If needed, order the following additional parts:
Cover plate/SPS [03102482-xx]
Hose holder/SPS [03102480-xx]
Overview
Fig.527: Coil hose – old and new version
A = Old version of Pin Picker
B = New version of Pin Picker
1. Pneumatic connection on return cylin-
der
2. Strain relief on return cylinder
2a: Old version
2b: New version
3. Coil hose
4. Strain relief on the pneumatic cylinder
guidance
4a: Old version
4b: New version
5. Valve terminal