00198829-01_SM_X-Series-S_Hxxxx_EN - 第372页
9 Component feeding 9.6 Smart Pin Support 372 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 9.6.13 Replacing the bottom sensor Parts, equipment and tools ● Inductive sensor assembly, bottom SPS [03090192Sxx] ● A…
9 Component feeding
9.6 Smart Pin Support
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 371
9.6.12 Replacing the top sensor
Parts, equipment and tools
●
Top sensor [03093273Sxx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.532: Sensors
1. Control board
2. Fastening screw for top sensor
3. Fastening screw for bottom sensor
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
Fig.533: Screws fastening the guide
► Remove the two screws(2) fastening
the pneumatic cylinder guidance(1)
.
► Remove the screws holding the sensor.
► Unthread the sensor cable as far as the
board. Open the corresponding cable
ties to help you, if needed.
► Unplug the sensor cable from the
board. You may want to mark the posi-
tion to make clear assignment easier
later on.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► Fasten the sensor in the center of the slot.
► Check that the sensors switch properly.
The switch tag of the linear guide must have between 0.7 and 1.4 mm space to the sensor
above or below.
The top sensor must switch after 2mm when travelling downwards.
► Replace any opened cable ties.
9 Component feeding
9.6 Smart Pin Support
372 Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021
9.6.13 Replacing the bottom sensor
Parts, equipment and tools
●
Inductive sensor assembly, bottom SPS [03090192Sxx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.534: Sensors
1. Control board
2. Fastening screw for top sensor
3. Fastening screw for bottom sensor
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
Fig.535: Screws fastening the sensor mount
► Remove the two screws(1) fastening
the sensor mount.
► Remove the screws holding the sensor.
► Unthread the sensor cable as far as the board. Open the corresponding cable ties to help you,
if needed.
► Unplug the sensor cable from the board. You may want to mark the position to make clear as-
signment easier later on.
Installation
Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► Fasten the sensor in the center of the slot.
► Check that the sensors switch properly.
The switch tag of the linear guide must have between 0.7 and 1.4 mm space to the sensor
above or below.
The bottom sensor must switch after 112 mm when travelling downwards.
► Replace any opened cable ties.
9 Component feeding
9.6 Smart Pin Support
Service Manual SIPLACE X-Series S (from Hxxxx) 01/2021 373
9.6.14 Replacing the one-way restrictor
Parts, equipment and tools
●
One-way restrictor AS1201F-M3-04 [03088646-xx]
●
Assembly instructions "Smart Pin Support" for SIPLACE X‑SeriesS [DEEN:00197394‑xx]
Overview
Fig.536: One-way restrictor
1. One-way restrictor
CAUTION!
The one-way restrictor is preset. Do
not change this setting!
If the setting is changed, you will need
to replace the one-way restrictor.
.
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the Pin Picker.
9.6.1 "Replacing the Pin Picker Assembly" [}357]
Fig.537: Screws fastening the valve terminal
► Remove the two screws fastening the
(1)
valve terminal. These are on the
back of the Pin Picker.
► Pull the pneumatic hose off the one-way restrictor.
► Unscrew and remove the one-way restrictor from the valve terminal.
Installation
Follow the removal instructions in reverse order for installation.