444CEMM2(CM201).pdf - 第41页

Page 3-1 Chapter 3 SOLUTIONS FOR ERROR Solutions for error This chapter describes solving errors. Many errors happen because sensors set on each point of the machine detect abnor- mal condition, or the movable section of…

Page 2-40

444C-EEn-MpMpMp-010

Procedures of Machine Parameter Teaching

444C-E-MMA02-A04-01

21. Press

UNLOCK

+ Jig remove .

• A message appears.

22. If you perform the teaching on the

other stage, press No ; then return to

step 2. When the teaching on all the

stages is complete, press

UNLOCK

Yes .

• Detach the illumination, which has been put on

the support blocks, and the 1005R feeder.

23. Press .

24. Press

UNLOCK

+ Run .

Page 3-1

Chapter 3

SOLUTIONS FOR ERROR

Solutions for error

This chapter describes solving errors.

Many errors happen because sensors set on each point of the machine detect abnor-

mal condition, or the movable section of the machine has trouble. Check the name of

the sensor related to the errors by the error list, and the position of the sensor by the

load arrangement. Refer to the input and output checks of the machine, for the state

of the sensor and the movement of the movable section of the machine. When the

error happens, press to stop the buzzer. After that, see on the touch

panel or error list on the Maintenance Manual, and carry out the solution.

3-1 Error Messages (Error list)

3-2 Check and Solutions

3-3 Load Arrangement

3-4 Load List

3-5 Input and Output Check of the Machine (Checking the State of Sensor,

Movement of Movable part, and Checking Method)

444C-E-MMA03-A01-01

433C-JOp-Er-001

Page 3-2

444C-E-MMA03-A01-00

3-1 Error Messages (Error List)

3-1-1 Use of Error Message List

This section describes how to use the error message list. When the error occurs during using this

machine, check the message displayed on the screen, and take the check and solutions, referring

to the error message list described at 3-1-2 afterward.

For taking the check and solutions, in putting your hand into the machine, make sure of turning off

the servo switch.

M67EB

TURN OFF THE SERVO SWITCH BEFORE PLACING YOUR HANDS IN ACTIVE

PART OF THE MACHINE FOR ADJUSTMENT.

You will have serious injury if the machine is actuated.

WARNING

444C-418TE

I/O No.Error messages Causes of Error

Check and Solutions

Reference

3-1-2 Errors during PT Network

segassemrorrE sesuaC snoitulosdnakcehC

-refeR

ecne

tuo-emitnoitacinummocTP

forewopehtroelbackrowtenehtfonoitcennocsiD

.nodenruttonsibuheht

.metsyskrowtenehtkcehC

tsixetonatadgocerTP

ehtretfaatadnidnuoftonsiatadnoitingocerehT

.TPmorfdaolnwod

∗ kcolb(05woleb.oNecnereferehtgnisutonnI

sihttsixetonodatadnoitingocerehtsa,)hctam

.derongiebnactitub,sraepparorre

:)hctamkcolb(05wolebrebmunFERgnisusiD

.noogot"KO"sserpdnaegassemehterongI

:)hctamkcolb(05wolebrebmunFERgnisunI

.atadnoitingocerehtetaercdnagnihcaettuoyrraC

rorrenoitacinummocTP

forewopehtroelbackrowtenehtfonoitcennocsiD

.nodenruttonsibuheht

.metsyskrowtenehtkcehC

443C-025TE

segassemrorrE .oNO/I sesuaC snoitulosdnakcehC

-efeR

ecner

rorresisongaid-fleS

)enilelohw(

.detcetederarorresisongaid-flesderetsigernU)1 .tifosumrofnidnaetatsehtkcehC)1-

atadtcudorplagellI

)enilelohw(

.atadnoitcudorpehtnieraatadlamronbA)1 ”,noitacifidoMataD“fo”kcehCataD“tarorreehtkcehC)1

.eulavlamronehtretnedna