CP-7[732-742]-series Mechanical Reference(2.9E) - 第119页
T020 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 ST3 Nozzle Clutch Every 3 months Every 3 months Every 3 months Monthly Every 3 months Monthly Monthly Monthly Monthly Every 3 months Monthly…
Lubrication Checklist
T010Ec
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Daphne Exponex No. 2
Multemp LRL3
Daphne Super Multi Oil 32
Daphne Exponex No. 2
Multemp LRL3
Daphne Super Multi Oil 32
Multemp SRL
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
Every 3 months
Monthly
Every 3 months
Every 3 months
Monthly
Every 3 months
Monthly
Every 6 months
Every 6 months
Every 6 months
Every 6 months
Every 3 months
Every 3 months
Monthly
Monthly
Monthly
Monthly
Monthly
Monthly
Monthly
Every 3 months
Every 3 months
Every 3 months
Monthly
Weekly
Weekly
Monthly
Lubrication points
Schedule
CheckTypes of lubricant
XY-table
Conveyors
Carriers
Tape advance
link
Cam box
Tape cutter
X-axis LM block
X-axis ball screw
X-axis screw cover
Y-axis LM block
Y-axis ball screw
Y-axis screw cover
Z-axis ball screw
Ball screw
Shaft
Lifter guide bar
LM block (742ME, 742E)
LM rail
Cam follower
Tape feed lever
Shaft
Joint
Cam
Cam lever pivot (7 points)
Cam lever bearing
NZ-axis ball screw
NZ-axis LM rail
NZ-axis holder
NZ-axis LM block
-axis connecting pin
Movable cutter
Cam follower
Thrust bearing
Part 3 Chapter 2 Lubrication
Edition 2.9 3-2-27 CP-7 series Mechanical Reference
T020
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
ST3 Nozzle Clutch
Every 3 months
Every 3 months
Every 3 months
Monthly
Every 3 months
Monthly
Monthly
Monthly
Monthly
Every 3 months
Monthly
Monthly
Monthly
Every 3 months
Every 3 months
Every 3 months
Every 3 months
Monthly
Monthly
Every 3 months
Monthly
Monthly
Every 3 months
Every 3 yrs or
12,000 hrs
Every 6 months
*: Fuji special blend
Lubrication points
Schedule
CheckTypes of lubricant
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Multemp LRL3
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
AFC grease
Daphne Exponex No. 2
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
SHC 630
Turbine oil + NASKALUBE*
Rod ends
D-axis carriers
Rotary head
ST9 Air valve push pin
Parts reject unit
Pallet table
Rear cover
Nozzle changer
LM Block
Rod end
D-axis LM block
D-axis ball screw
Cam follower
Turret groove
Helical gear
LM rail
Spline shaft
Wave washer
Pin
Valve push pin
Valve push pin
Cam follower
LM rail
Pallet clamp surface
Clamp pin
Spline shaft
Beveled gear
Moveable sections on
the lever
Clutch engagement
surface
Thrust bearing
Slide rail
Oil cooler
Air cylinder
Index unit
Cam lever
Part 3 Chapter 2 Lubrication
Edition 2.9 3-2-28 CP-7 series Mechanical Reference
3. Replacing Consumable Parts
3.1 Replacing Nozzles
Point
A nozzle which becomes bent, deformed, or clogged, can cause part pick-up errors and
must be replaced. When replacing a nozzle, use care to avoid losing its internal spring.
Procedure
WARNING
Be sure to turn the main power off before performing this
procedure.
1. Remove the nozzle and spring as shown in the figure below.
Caution:
1. When removing the nozzle, take care not to lose the internal spring. Also check that
the spring is not left within the nozzle holder.
2. To avoid nozzle bend, do not hold the nozzle at the tip during removal.
2. Reverse the removal procedure to attach a new nozzle.
Press and turn
Remove slowly
Nozzle
Spring
C7SM3050a
Part 3 Chapter 3 Replacing Consumable Parts
Edition 2.7 3-3-1 CP-7 series Mechanical Reference