CP-7[732-742]-series Mechanical Reference(2.9E) - 第120页
3. Replacing Consumable Parts 3.1 Replacing Nozzles Point A nozzle which becomes bent, deformed, or clogged, can cause part pick-up errors and must be replaced. When replacing a nozzle, use care to avoid losing its inter…
T020
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
ST3 Nozzle Clutch
Every 3 months
Every 3 months
Every 3 months
Monthly
Every 3 months
Monthly
Monthly
Monthly
Monthly
Every 3 months
Monthly
Monthly
Monthly
Every 3 months
Every 3 months
Every 3 months
Every 3 months
Monthly
Monthly
Every 3 months
Monthly
Monthly
Every 3 months
Every 3 yrs or
12,000 hrs
Every 6 months
*: Fuji special blend
Lubrication points
Schedule
CheckTypes of lubricant
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Multemp LRL3
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
AFC grease
Daphne Exponex No. 2
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
AFC grease
Daphne Exponex No. 2
Daphne Exponex No. 2
Daphne Exponex No. 2
AFC grease
Daphne Exponex No. 2
SHC 630
Turbine oil + NASKALUBE*
Rod ends
D-axis carriers
Rotary head
ST9 Air valve push pin
Parts reject unit
Pallet table
Rear cover
Nozzle changer
LM Block
Rod end
D-axis LM block
D-axis ball screw
Cam follower
Turret groove
Helical gear
LM rail
Spline shaft
Wave washer
Pin
Valve push pin
Valve push pin
Cam follower
LM rail
Pallet clamp surface
Clamp pin
Spline shaft
Beveled gear
Moveable sections on
the lever
Clutch engagement
surface
Thrust bearing
Slide rail
Oil cooler
Air cylinder
Index unit
Cam lever
Part 3 Chapter 2 Lubrication
Edition 2.9 3-2-28 CP-7 series Mechanical Reference
3. Replacing Consumable Parts
3.1 Replacing Nozzles
Point
A nozzle which becomes bent, deformed, or clogged, can cause part pick-up errors and
must be replaced. When replacing a nozzle, use care to avoid losing its internal spring.
Procedure
WARNING
Be sure to turn the main power off before performing this
procedure.
1. Remove the nozzle and spring as shown in the figure below.
Caution:
1. When removing the nozzle, take care not to lose the internal spring. Also check that
the spring is not left within the nozzle holder.
2. To avoid nozzle bend, do not hold the nozzle at the tip during removal.
2. Reverse the removal procedure to attach a new nozzle.
Press and turn
Remove slowly
Nozzle
Spring
C7SM3050a
Part 3 Chapter 3 Replacing Consumable Parts
Edition 2.7 3-3-1 CP-7 series Mechanical Reference
3.2 Replacing the Fluorescent Nozzle Stickers
Point
Fluorescent nozzle stickers which become soiled and cause vision processing errors must
be replaced.
Procedure
1. Wash hands before replacing the sticker.
2. Use a cutter to peel (from outer edge) the old sticker off the nozzle disk.
3. Use a cloth to wipe any residual adhesive off the disk.
4. Verify that the new sticker is not soiled or damaged.
5. Peel the backing off the new sticker, and punch the nozzle tip through from the
fluorescent side.
Note: Punching the nozzle tip through from the adhesive side will destroy the fluorescent
coating around the hole.
6. Align the nozzle and sticker centers, and push the sticker into place using the jig.
Be sure that there is no gap between the nozzle disk and the sticker.
Note: Make sure that the sticker is attached firmly to the nozzle.
Attached neatly without lifting.
C7SM3028
Nozzle seal
Nozzle seal
Jig ( DCPJ0460 )
Jig
( ADCPJ8240 )
C7SM3051a
Part 3 Chapter 3 Replacing Consumable Parts
Edition 2.7 3-3-2 CP-7 series Mechanical Reference