00195011-01 - 第44页

Installation Manual, Station Software Version 408.01 Edition 03/2006

The chipset suppurts automatic detection and correction of DRAM bit errors using ECC as well as

normal parity handling. This setting is only effective if DIMMs with a parity bit are used.

None No error handling. Bit errors are not detected.

4.3.1.10 Setup page "Peripherals"

┌────────────────────────┤ Peripherals ├────────────────────────┐

│ │

│ ┌─Serial / Parallel Ports───────────────────────┐ │

│ │ Serial Port A: 3F8h, IRQ4 │ ╔══════╗ │

│ │ Serial Port B: 2F8h, IRQ3 │ ║ OK ║ │

│ │ Parallel Port: 378h, IRQ7 Bidirectional │ ╚══════╝ │

│ └───────────────────────────────────────────────┘ │

│ ┌─IDE / Floppy Controller───────────────────────┐ ┌──────┐ │

│ │ Primary IDE: Enabled │ │Cancel│ │

│ │ Secondary IDE: Disabled │ └──────┘ │

│ │ Floppy Disks: Enabled Normal │ │

│ └───────────────────────────────────────────────┘ ┌───────┐ │

│ ┌─Miscellaneous─────────────────────────────────┐ │Default│ │

│ │ PS/2 Mouse: Disabled │ └───────┘ │

│ └───────────────────────────────────────────────┘ │

│ Press [F1] key for help │

└───────────────────────────────────────────────────────────────┘

This setup page allows you to make settings for the peripherals.

Serial / Parallel Ports

Serial Port A: Sets the I/O addresses and IRQs of serial port A:

3F8h, IRQ4

Serial Port B: Sets the I/O addresses and IRQs of serial port B:

2F8h, IRQ3

Parallel Port: Sets the I/O addresses, IRQs and mode of the parallel port:

378h, IRQ7

Bidirectional

Port can be used for input and output

IDE/Floppy Controller

Primary IDE:

Enabled

IDE channel enabled

Secondary IDE:

Disabled

IDE channel disabled

Floppy Disks:

Enabled

Floppy controller enabled

It is also possible to assign the drive letters: Normal Normal operation

43 of 104

Installation Manual Station Software Version 408.01

Miscellaneous

PS/2 Mouse:

Disabled

PS/2 mouse deactivated

4.3.1.11 Setup page "PCI Setup"

┌────────────────┤ PCI Setup ├───────────────┐

│ ┌──────────────────────────┐ │

│ │ MultiMedia Enable: [ ] │ ╔══════╗ │

│ └──────────────────────────┘ ║ OK ║ │

│ ┌──────────────────────────┐ ╚══════╝ │

│ │ PCI INT IRQ │ ┌──────┐ │

│ │ A: 7 │ │Cancel│ │

│ │ B: NONE │ └──────┘ │

│ │ C: NONE │ ┌───────┐ │

│ │ D: NONE │ │Default│ │

│ └──────────────────────────┘ └───────┘ │

│ Press [F1] key for help │

└────────────────────────────────────────────┘

This page is used to make specific PCI settings.

MultiMedia Enable:

This option activates "video palette snooping". This may be required if an ISA video adapter and a

PCI video overlay adapter are installed and incorrect colors are displayed.

PCI-Interrupt-Routing

For each PCI INT (= motherboard INT) an IRQ can now be defined in the setup fields.

Since the LAN card of the M54 is designed as a PCI card, PCI INT A is required.

In Setup, IRQ 7 is to be entered for PCI INT A. During start-up, the BIOS will then assign this IRQ to

the PCI card.

44 of 104

Installation Manual, Station Software Version 408.01 Edition 03/2006

4.3.1.12 Setup page "IMC Interrupts"

┌─────────────────────┤ IMC Interrupts ├────────────────────────┐

│ │

│ ┌───────────────────────────────────────────────┐ ╔══════╗ │

│ │ PC-IRQ IRQ-Source IRQ-Mode │ ║ OK ║ │

│ │ 3 onboard COM transparent │ ╚══════╝ │

│ │ 4 onboard COM transparent │ ┌──────┐ │

│ │ 5 SMP_INT2 transparent │ │CANCEL│ │

│ │ 6 onboard Floppy transparent │ └──────┘ │

│ │ 7 not assigned transparent │ ┌───────┐ │

│ │ 10 SMP_INT5 transparent │ │Default│ │

│ │ 11 SMP_INT6 transparent │ └───────┘ │

│ │ 14 onboard IDE transparent │ │

│ └───────────────────────────────────────────────┘ │

│ │

│ Press [F1] key for help │

└───────────────────────────────────────────────────────────────┘

The electronic interrupt matrix is to be set up as follows on this page.

PC-IRQ IRQ-Source

3 through 14 Unassigned

3

Onboard COM

4

Onboard COM

SMP_INT2 SMP16 interrupt c19 5

Onboard Floppy Floppy interrupt 6

7

Not assigned

SMP_INT5 SMP16 interrupt c25 10

SMP_INT6 SMP16 interrupt c27 11

14 Onboard HD Hard disk interrupt

IRQ-Mode

Transparent Interrupt line is connected through to the interrupt source (default)

45 of 104