00196497-07_SM_SXDX12_en - 第131页

Service Work Conveyor 3.5.4 Replacing the CPP Head Placement heads Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 131 3.5.4.1 3 . 5 . 4 . 1 P r e p a r in g t h e H e a d f o r t h e I n s t a lla t io n H e ig h t Preparin…

100%1 / 334
Service Work Conveyor
Placement heads 3.5.4 Replacing the CPP Head
130 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
► Remove all four screws fastening the head with a long Torx screwdriver.
► Carefully lift the head out of the locating pins on the head plate/from the hook.
► If you need to perform further work on this head (e.g. replacing spare parts), fit the head to the head
mount [03056231-xx].
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
3.5.4.1 Preparing the Head for the Installation Height [ ➙ 131]
3.5.7 Installation Positions on the Head Plate [ ➙ 138]
CAUTION
Installation instructions
► Observe the correct installation height of the head! Read the service manual for your place-
ment head for more information.
► If you replace the head without the component camera, you will need to fit the old camera
onto the new head. Read the service manual for your placement head for more information.
► Make sure that the assembly position on the head plate is correct.
► Tighten the four fastening screws with a torque of 2.7 Nm.
► Make sure that the flat ribbon cable is run correctly to the head adapter. (see below)
Correct running of flat ribbon cable to head adapter
► Make sure that the flat ribbon cable is run correctly to
the head adapter. In particular, the cables must lie in-
side one another at the 90 degrees turn (1) and not
on top of one another, otherwise the connections on
the head adapter could be easily confused.
Service Work Conveyor
3.5.4 Replacing the CPP Head Placement heads
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 131
3.5.4.1
3.5.4.1 Preparing the Head for the Installation Height
Preparing the Head for the Installation Height
Overview
CAUTION
Different heights
The placement head can be installed at two different heights. CPP_L corresponds to a compo-
nent height of six mm. CPP_H corresponds to a component height of 11.5 mm.
If the CPP head is used in a placement area with stationary camera, TwinHead or WPC, it may
only be used in the upper position.
1. Fastening screws on the left side
2. Fastening screws on the right side
This diagram shows the fastening screws in the "head at
top" position.
1. Holding bracket
2. "Head at bottom" position
3. "Head at top" position
4. Fixture holes with bushings
Service Work Conveyor
Placement heads 3.5.5 Replacing the Twin/VHF Head
132 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
Conversion to another installation height
3.5.5
3.5.5 Replacing the Twin/VHF Head
Replacing the Twin/VHF Head
Parts, Equipment and Tools
▪ Select the relevant placement head:
– Twin Pick&Place module [03033628-xx]
– Twin Pick&Place module THK R2 [03097485-xx]
– Very High Force P&P head [00119813-xx]
– Very High Force Twin head [00119814-xx]
– Twin VHF [03096701-xx]
▪ Torque screwdriver 1-5 Nm [03078400-xx]
▪ Extension/straight TX20 [03073256-xx]
▪ Extension/straight [03043440-xx]
▪ Bit holder for Torque Vario-S screwdriver [03078706-xx]
▪ Calibration tool version 3 [03010565-xx]
SXDX12V1V2 Only
▪ If required, Camera view screen Twin-Head, SX1/2 [03079524-xx]
▪ For additional work on the placement head:
Head assembly stand [03056231-xx
Service manual "TH/VHF head" [DE: 00197468-xx]. [EN: 00197469-xx].
Overview
The Twin VHF consists of two identical Twin segments, which are fitted at an angle of 180°.
1. Drilling for the fastening screw of the bushing in "head
at bottom" position
2. Drilling for the fastening screw of the bushing in "head
at top" position
3. Bushing
All four bushings and the holding bracket must either be
fixed in top or bottom position.
Proceed as follows when replacing the bushings:
► Undo the fastening screws of the bushings.
► Insert the bushings in the correct position and re-
tighten them.
► Perform these steps for all four fastening bushings
and the holding bracket of the head.
NOTICE
Module 1 and 2
The removal procedure is described here for module 1 (left). Removal for module 2 (right) is the
same.
► In the case of older Twin heads, you need to remove module 1 before you can remove
module 2. During installation, module 2 needs to be fitted before module 1.
► In the case of newer Twin heads and all Twin VHF heads, the modules can be removed
and fitted individually.