00196497-07_SM_SXDX12_en - 第135页
Service Work Conveyor 3.5.6 Replacing the DLM4 Head Placement heads Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 135 3.5.6 3 . 5 . 6 R e p la c in g t h e D L M 4 H e a d Replacing the DLM4 Head Parts, Equipment and Tools…
Service Work Conveyor
Placement heads 3.5.5 Replacing the Twin/VHF Head
134 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
► If you need to perform further work on this head (e.g. replacing spare parts), fit the head to the head
mount [03056231-xx].
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
See also
4.9.2 Calibration [ ➙ 294]
3.5.7 Installation Positions on the Head Plate [ ➙ 138]
4.9.2.2 Calibrating the Heads and Cameras (SW70x) [ ➙ 295]
Each module is fixed with four screws to the head plate
and is positioned with two pins.
► Remove the four M4x14 fastening screws (1) with a
long Allen key.
► Pull the module out of the locating pins.
CAUTION
Installation instructions
► Fit the fastening screws on the other side of the module, if needed (see above).
► Make a note of the force values for the new module. These force values can be found on
a label at the side of the module.
► Make sure that the assembly position is correct.
► Perform a head calibration.
Service Work Conveyor
3.5.6 Replacing the DLM4 Head Placement heads
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 135
3.5.6
3.5.6 Replacing the DLM4 Head
Replacing the DLM4 Head
Parts, Equipment and Tools
▪ DLM4 head with 12 segments (without sleeves) [03082533-xx]
▪ Adapter plate assembly DLM4-DX1/2 [03082158-xx], if necessary
▪ Torque screwdriver 1-5 Nm [03078400-xx]
▪ Extension/straight TX20 [03073256-xx]
▪ Bit holder for Torque Vario-S screwdriver [03078706-xx]
▪ Extension/straight [03043440-xx]
▪ Extension / with joint [03042635-xx]
▪ Torx Allen screwdriver TX8 [03080081-xx]
▪ Calibration tool version 3 [03010565-xx]
▪ 12x calibration nozzles type 3056 [00330538-xx]
▪ For additional work on the placement head:
Head assembly stand [03056231-xx]
Service manual "DLM3/DLM4/DLM head" [DE: 00197466-xx] [EN: 00197467-xx]
Overview
NOTICE
The adapter plate is only needed for the DLM4 heads.
Adapter plate assembly DLM4-DX1/2 [03082158-xx]
1. Fastening screws for the adapter plate on the head
plate
2. Fastening screws for the DLM head on the adapter
plate
1. Illumination control
2. Vacuum generator
3. Four fastening screws M4x18 on the adapter plate
Service Work Conveyor
Placement heads 3.5.6 Replacing the DLM4 Head
136 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
Removal
► If possible, use calibration nozzles of type 3056 [00330538-xx] (with the help of the station software).
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
1. Head interface and head adapter
2. Head plate
3. Adapter plate (between head plate and head)
4. Screws fastening the head to the adapter plate
5. Vacuum generator
1. Compressed air hoses
2. Vacuum generator
1
1
2
NOTICE
Marking the connections
Before you unplug electrical or pneumatic connections, mark their positions, to make clear as-
signment easier later on.
CAUTION
Do not place the head down on the valve positioning drives!
The valve positioning drives of the star can be misaligned under mechanical loads.
► After removal, place the head carefully down on a soft surface, without putting pressure on
the valve positioning drives.