00196497-07_SM_SXDX12_en - 第146页
Service Work Conveyor Conveyor 3.6.1 Loosening the Conveyor Side Clamps 146 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 0440 - Tit le Versi on 2 Version 2 0445 - V ersion 2 0460 - Tit le Versi on 3 Version 3 0465 - V ers…
Service Work Conveyor
3.6.1 Loosening the Conveyor Side Clamps Conveyor
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 145
3.6.1.2
3.6.1.2 Moving the Conveyor Sides by Manually Releasing the Side Clamps
Moving the Conveyor Sides by Manually Releasing the Side Clamps
0200 – Parts etc. - SXDX12
Parts, equipment and tools
▪ Depending on your clamping version, you may need the following per side:
2x ISO4762-M3x35-A2-70 [03043114-xx] or
2x ISO8734-3x30-A-ST [03015760-xx] or
2x ISO4762-M3x16-A2-70 [03042545-xx]
Procedure
► Move the conveyor sides to a position which gives you good access to the clamps.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
0400 - Advance Set for Multiple Versions
Select the applicable version of the clamp:
0420 - Title Version 1
Version 1
0425 - Version 1 - SXDX12V1V2 (V1 only FS02) X34iS
NOTICE
Marking the starting positions
After completing this task, it is helpful to move the conveyor sides back to their approximate
starting positions.
► You may want to mark the current positions of the conveyor sides.
Do not mark the clamping surface or the guide rails.
CAUTION
Loosen all clamps
You always need to loosen all clamps for one conveyor side.
► Loosen the conveyor side clamps.
To do this, press the clamp (1) (e.g. with a screwdriv-
er) upwards and turn or insert a screw (M3x16) into
the hole (2).
CAUTION!
Make sure that you do not distort the guide plate (3). If
you do, this could lead to problems with recognizing the
position of the conveyor side.
Service Work Conveyor
Conveyor 3.6.1 Loosening the Conveyor Side Clamps
146 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
0440 - Title Version 2
Version 2
0445 - Version 2
0460 - Title Version 3
Version 3
0465 - Version 3
► Repeat these steps for all clamps on the sides concerned.
You can now move the sides.
► Loosen the clamps on the conveyor sides.
To do this, remove the disks above the clamp com-
pression springs (2 screws for each disk). To do this,
undo both screws (1) on the clamps (2 x for each con-
veyor side).
CAUTION!
Compression springs
The compression springs are tensioned.
Make sure that you do not lose these.
► Loosen the conveyor side clamps.
To do this, press the lever (1) upwards and push a
suitable pin or a screw into the hole (2).
CAUTION
Always loosen all clamps for one conveyor side!
► Always loosen all clamps for one conveyor side!
SX1/SX2/DX1/DX2: 2 clamps per conveyor side
SX4/DX4/X series S: 3 clamps per conveyor side.
► If you do not loosen all clamps for the conveyor side, this could be easily damaged.
CAUTION
Moving the sides
► When the clamp is manually loosened, make sure that you only move the conveyor sides
by pushing against the clamping units.
► Make sure that you always move the conveyor sides parallel.
► Take care not to distort or trap the conveyor sides when pushing!
Service Work Conveyor
3.6.1 Loosening the Conveyor Side Clamps Conveyor
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 147
Restoring the clamp
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
CAUTION
Installation instructions
► After completing the work, push the conveyor sides back into their approximate starting po-
sition.
► Make sure that the conveyor sides are back in their original positions after switching on.
► Perform a reference run.
► Perform side calibration for the fixed side on the left and right. If you do not, not all conveyor
sides will be calibrated.
This calibration is needed to ensure that the conveyor sides are positioned correctly.
► SX1/SX2 V2 and X-Series S only: Calibrate the board PCB sensors.
► Use a board to test the parallelism. This board must be transported evenly through the en-
tire conveyor (see also Setting the Parallelism of the Conveyor Sides).
► Re-establish the original conveyor configurations:
For more information, go to Service menu - Conveyor configuration - Set options for con-
veyor fixed rail.
Select one of the positions and click on the Adjust configuration button.
Then reset the conveyor sides to the previous configuration.