00196497-07_SM_SXDX12_en - 第148页

Service Work Conveyor Conveyor 3.6.2 Lifting table 148 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 3.6.2 3 . 6 . 2 L if t in g t a b le Lifting table 3.6.2.1 3 . 6 . 2 . 1 R e p la c in g t h e L if t in g T a b le U n i…

100%1 / 334
Service Work Conveyor
3.6.1 Loosening the Conveyor Side Clamps Conveyor
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 147
Restoring the clamp
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
CAUTION
Installation instructions
► After completing the work, push the conveyor sides back into their approximate starting po-
sition.
► Make sure that the conveyor sides are back in their original positions after switching on.
► Perform a reference run.
► Perform side calibration for the fixed side on the left and right. If you do not, not all conveyor
sides will be calibrated.
This calibration is needed to ensure that the conveyor sides are positioned correctly.
► SX1/SX2 V2 and X-Series S only: Calibrate the board PCB sensors.
► Use a board to test the parallelism. This board must be transported evenly through the en-
tire conveyor (see also Setting the Parallelism of the Conveyor Sides).
► Re-establish the original conveyor configurations:
For more information, go to Service menu - Conveyor configuration - Set options for con-
veyor fixed rail.
Select one of the positions and click on the Adjust configuration button.
Then reset the conveyor sides to the previous configuration.
Service Work Conveyor
Conveyor 3.6.2 Lifting table
148 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.6.2
3.6.2 Lifting table
Lifting table
3.6.2.1
3.6.2.1 Replacing the Lifting Table Unit
Replacing the Lifting Table Unit
Parts, equipment and tools
▪ Lifting table single conveyor [03055147-xx] or
▪ Lifting table dual conveyor [03055148-xx]
▪ Depth measuring gauge (200 mm) [03079617-xx]
Overview
Removal
► Use the software to move the conveyor sides to a position which gives you good access to the lifting
table fixtures.
► Switch off the machine and secure it to prevent unauthorized reactivation. Observe the instructions
in section "1.2 Preparatory Work..." [ ➙ 13].
► Loosen the clamps on the conveyor sides (see "3.6.1 Loosening the Conveyor Side Clamps"
[ ➙ 143]).
► Loosen the screws fastening the two lifting table plates (four for each lifting table plate) and remove
the lifting table plates from the machine.
► Mark the positions of the lifting table plate guides to make it easier to refit them later on. Make sure
you do not confuse these.
1. Lifting table motors
2. Holes for the fastening screws
3. Four lifting table plate guides
These are part of the lifting mechanism.
4. Fixtures for cable clamps
NOTICE
Single, dual conveyor
The replacement is shown in the diagram using the example of a lifting table unit for the dual
conveyor (DC). Replacement of the lifting table unit for the single conveyor (SC) is the same.
NOTICE
Lifting table up?
If the lifting table stays in the top position, you first need to disconnect the motor from the rods
(see "3.6.2.1.1 Manually Lowering the Lifting Table" [ ➙ 149]).
Service Work Conveyor
3.6.2 Lifting table Conveyor
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 149
► Unplug all electrical connections to the lifting table motors (three for each motor).
► Open the cable clamps for the electrical connections.
► Mark the direction of transport for the lifting table. This helps you avoid unintentionally fitting the lifting
table at the wrong angle later on (turned by 180 degrees).
► Loosen the six screws (EC: four screws) fastening the lifting table.
► Carefully lift the lifting table out of the machine.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
Manually Lowering the Lifting Table
If the lifting table stays in the top position, it can be manually lowered in the event of an emergency.
Procedure
CAUTION
Screws
Make sure that you do not loosen any other screws!
CAUTION
Heavy machine part!
When removing the lifting table, remember it is heavy. You may need to enlist the help of a sec-
ond person.
CAUTION
Installation instructions
► Make sure that the lifting table is aligned correctly in the direction of transport.
► Before you finally fix the lifting table into place, push it up to the stop in the direction of out-
put. This ensures that the lifting table is parallel.
1. Lifting table plate
2. Holes in the lifting table plate
3. Motor.
4. Rods
5. Access to connection screw between rods and motor
► Loosen the screw connecting the rods with the motor,
through the holes in the lifting table plate.
► You can now move the lifting table downwards.