00196497-07_SM_SXDX12_en - 第210页
Service Work Conveyor COT insert 3.10.2 Replacing the SX1/SX2 Component Trolley Feed D evice Assembly 210 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 The posit ion of the fast ening scre ws (4) and (5) depends o n the po…
Service Work Conveyor
3.10.2 Replacing the SX1/SX2 Component Trolley Feed Device Assembly [03059353-xx] COT insert
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 209
3.10.2.1
3.10.2.1 Fitting the Downholder
Fitting the Downholder
Preparing the downholder
Depending on the position of the component trolley (inside/outside), the downholder pin [03085247-xx]
is fitted either in position (1) or (2). This is then secured in place with a screw ISO4762-M6x12-A2-70
[03042572-xx].
After installation, the docking aid (3) docking aid on the downholder is always in the same position as
the docking unit that was previously dismantled (near the protective cover). The downholder pin and
therefore the assembly position of the downholder depends on the table position (inside/outside).
NOTICE
Only when table position changed
The downholder pin only needs to the converted if the table position inside/outside has been
changed.
1 Pin DIN6325-10-M6x30-St [00358814-xx]
at position inside
2 Pin DIN6325-10-M6x30-St [00358814-xx]
at position outside
3 Docking aid 4 Screw ISO4762-M8x40-A2-70 [03042589-
xx]
5 Screw ISO4762-M8x40-A2-70 [03042589-
xx]
Service Work Conveyor
COT insert 3.10.2 Replacing the SX1/SX2 Component Trolley Feed Device Assembly
210 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
The position of the fastening screws (4) and (5) depends on the position of the COT insert.
When the table is in the inner position, the downholder pin (1) is moved approx. 125 mm inwards, to-
wards the docking aid (3) and the downholders are fixed with two new screws each to the position (4),
together with the COT insert.
When the table is in the outer position, the downholder pin (2) is underneath the docking aid (3) and the
downholders are fixed with two new screws each to the position (4), together with the COT insert.
1 Pin DIN6325-10-M6x30-St [00358814-xx]
at position inside
2 Pin DIN6325-10-M6x30-St [00358814-xx]
at position outside
3 Docking aid 4 Screw ISO4762-M8x40-A2-70 [03042589-
xx]
5 Screw ISO4762-M8x40-A2-70 [03042589-
xx]
Service Work Conveyor
3.10.2 Replacing the SX1/SX2 Component Trolley Feed Device Assembly [03059353-xx] COT insert
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 211
Fitting the right downholder
► Remove the two screws (4) and (5) on the right side of the COT insert. The screws are underneath
the COT insert cylinder.
► Place the "downholder COT-i right assembly" [03085834-xx] on the right side of the COT insert so
that the holes are aligned with one another.
► Screw the downholder tight with the two new screws (4) and (5).
► The downholder pin (2) must always be approx. 10 mm before the claws of the insert and the dock-
ing aid (3), behind the machine protection (cover flap).
1 Pin DIN6325-10-M6x30-St [00358814-xx]
at position inside
2 Pin DIN6325-10-M6x30-St [00358814-xx]
at position outside
3 Docking aid 4 Screw ISO4762-M8x40-A2-70 [03042589-
xx]
5 Screw ISO4762-M8x40-A2-70 [03042589-
xx]
NOTICE
Screws
Insert the new screws into the holes in the downholder and position the downholder together
with the screws onto the COT insert.