00196497-07_SM_SXDX12_en - 第224页
Service Work Conveyor Cutter 3.11.1 Replacing the Cutter [03063781Sxx] 224 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 ► Carefully lift the cutter out of the machine. WARNING! Risk of injury when releasing the fixtures! …
Service Work Conveyor
3.11.1 Replacing the Cutter [03063781Sxx] Cutter
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 223
3.11
3.11 Cutter
Cutter
3.11.1
3.11.1 Replacing the Cutter [03063781Sxx]
Replacing the Cutter [03063781Sxx]
Parts, Equipment and Tools
▪ Cutter [03063781Sxx]
▪ Help of second person, if needed
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
► Unhook the waste tape chute. Please also observe section "3.10.10 Replacing the Waste Tape
Chute" [ ➙ 221].
► Unplug all electrical and pneumatic connections to the cutter. You may want to mark their positions,
to make clear assignment easier later on.
1. Connection for control system
2. Solenoid valves
3. Short-stroke cylinder
CAUTION
Switch off the compressed air supply!
When working on the pneumatic system, always switch off the compressed air supply.
CAUTION
There is a risk of injuring yourself on the cutting edge of the blades.
► Do not reach into the cutting area.
NOTICE
COT insert
The cutter can be removed without dismantling the COT insert.
Service Work Conveyor
Cutter 3.11.1 Replacing the Cutter [03063781Sxx]
224 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
► Carefully lift the cutter out of the machine.
WARNING!
Risk of injury when releasing the fixtures!
The cutter (1) is only held by the fastening screws (2) and
is not supported by other parts.
If the 4 fastening screws are loosened without the cutter
being secured, this will fall down onto the bracket (5).
► Turn the two supporting screws (4) up to the top.
► Undo the 4 screws (2) fastening the brackets (3) of
the cutter and remove these brackets. The cutter is
now resting on the supporting screws.
CAUTION!
Only cutters with FS04:
There are small spacer disks on the top of the screw fix-
ture points for the mount (3). Make sure these are not
lost!
► Carefully lower the cutter onto the brackets by slowly
and evenly (right and left) lowering the supporting
screws.
► Turn the support plates (1) (angular plates) outwards
on the infrastructure cabinets.
To do this, loosen the screws fastening the support
plates.
Unhook the plates, rotate them and then retighten the
fastening screws.
NOTICE!
Support plates
You may need to fetch the support plates from another lo-
cation!
► The cutter can now be carefully pulled out towards
the front.
NOTICE
Heavy machine part!
► The cutter is heavy. You might need to enlist the help of a second person to prevent this.
Service Work Conveyor
3.11.1 Replacing the Cutter [03063781Sxx] Cutter
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 225
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
► Hook the waste tape chute into place. Please also observe section "3.10.10 Replacing the Waste
Tape Chute" [ ➙ 221]. Pay particular attention to the plastic strips and the fuses (if present).
See also
1.2 Preparatory Work... [ ➙ 13]
CAUTION!
Installation instructions
Cutters with FS04 have a spacer disk (1) at all 4 screw fix-
ture points (2).
Make sure that these disks are present when you fit the
cutter.
Otherwise there is a risk of head crash!