00196497-07_SM_SXDX12_en - 第240页

Service Work Conveyor Cutter 3.11.5 Replacing the Cutter Blades 240 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 Troubleshooting See also   3. 11.1 Rep lacing the Cu tter [0306 3781Sxx] [ ➙ 223] NOTICE Error: cutter tim…

100%1 / 334
Service Work Conveyor
3.11.5 Replacing the Cutter Blades Cutter
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 239
► Check the gap between the blades.
If the gap is not correct, check:
▪ Has the wrong downholder (version < 03) been fitted?
The downholders are coordinated to the cutter with version 04 (= with deflector).
▪ Whether the blades, tape deflector etc. were cleaned before installation
If the gap is correct:
► Fit the connector with two fastening screws. Secure the screws with Loctite.
► Fit the protective plates onto the elastomeric springs. Secure the screws with Loctite.
► Fasten the cables into place on the protective plates with the help of cable ties.
► Reconnect the valves to the electricity supply.
► Reconnect the valves to the pneumatic supply.
► Refit the back cover. Secure the screws with Loctite.
► Follow the removal instructions in reverse order for further installation.
Installation – final work
Grease the cutter (see the maintenance manual for your machine) as follows:
► Fill the "grease gun with hose for Y axis" (volume applied approx. 0.4 g) [00374563-xx] with
Klüberplex BEM 34-132.
► Install the used tape chute. Please also observe section "3.10.10 Replacing the Waste Tape Chute"
[ ➙ 221]. Pay particular attention to the plastic strips and the fuses (if present).
CAUTION
Check how the cables and hoses are run!
Make sure that the cables and hoses are not pinched or subjected to excess strain.
► Position the hose of the grease gun straight onto the
lubrication nipple.
NOTICE!
If the lubrication nipple no longer lets lubricant through or
if it is damaged, replace it (DIN71412-A-M6 [03036936-
xx]).
► Press grease into the tape cutter until it visibly pro-
trudes out again.
► Remove excess grease with a brush.
► Repeat these steps for the other side of the tape cut-
ter.
► Repeat these steps for each tape cutter.
► Spray Interflon Fin grease into a suitable container.
► Distribute the grease with a brush to the underside of
the fixed blade (1).
► Remove any excess grease on the contact
surfaces (3) of the blades and the lubrication
nipples (2).
Service Work Conveyor
Cutter 3.11.5 Replacing the Cutter Blades
240 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
Troubleshooting
See also
3.11.1 Replacing the Cutter [03063781Sxx] [ ➙ 223]
NOTICE
Error: cutter timing
If you are shown the machine error "cutter timing", this could be due to an imprecise arrange-
ment of the blades to one another. This arrangement can also be corrected when they are fitted.
► For more information about this, read section "3.11.6 Replacing the Elastomeric Spring
(Blade Damping)" [ ➙ 241].
Service Work Conveyor
3.11.6 Replacing the Elastomeric Spring (Blade Damping) Cutter
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 241
3.11.6
3.11.6 Replacing the Elastomeric Spring (Blade Damping)
Replacing the Elastomeric Spring (Blade Damping)
Parts, equipment and tools
▪ Elastomeric spring 20x8.5x22 (90 Shore A) [03096352-xx]
▪ Plastic stopper for cutter SX1/SX2 [03096297-xx]
▪ Setting gauge for proximity switch buffer [03097370-xx]
▪ Loctite 243 locking varnish 10 ml [00334892-xx]
Overview
NOTICE
Replace in pairs
We recommend that you always replace the elastomeric springs in pairs. However, they can be
replaced individually if necessary.
1. Elastomeric spring on cutter
1. Plastic stopper
2. Elastomeric spring
3. Washer
4. 2 x fastening screws
5. Protective plate