00196497-07_SM_SXDX12_en - 第250页

Settings Settings on the Basic Machine 4.2.1 Setting the Machine Covers 250 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 4.2.1.2 4 . 2 . 1 . 2 S e t t in g t h e C o v e r G u id a n c e Setting the Cover Guidance 4.2.1.3…

Settings

4.2.1 Setting the Machine Covers Measuring Equipment and Tools

Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 249

4 Settings

Settings

4.1

4.1 Measuring Equipment and Tools

Measuring Equipment and Tools

For more information about the measuring equipment and tools used, refer to the service section of our

homepage at www.siplace.com.

4.2

4.2 Settings on the Basic Machine

Settings on the Basic Machine

4.2.1

4.2.1 Setting the Machine Covers

Setting the Machine Covers

4.2.1.1

4.2.1.1 Overview

Overview

NOTICE

Example

The following settings are shown using the example of an SX2 machine. The procedure is the

same for other machines. Any differences will be explicitly indicated.

Settings (example of SX2 shown)

1. Setting the cover guidance

See "4.2.1.2 Setting the Cover Guidance" [ ➙ 250]

2. Setting the cover switch

See "4.2.1.4 Setting the Cover Switch" [ ➙ 251]

3. Setting the cover switch centering

See "4.2.1.5 Setting the Cover Switch Centering De-

vice" [ ➙ 252]

4. Setting the actuator

See "4.2.1.6 Setting the Actuator" [ ➙ 252]

5. Setting the bottom stop

See "4.2.1.7 Setting the Bottom Stop" [ ➙ 253]

6. Setting the rollers

See "4.2.1.8 Setting the Cover Rollers" [ ➙ 254]

CAUTION

SX1/SX2: closing the gantry changer doors

The gantry changer doors must remain closed during operation and be fixed in their set posi-

tion.

Settings

Settings on the Basic Machine 4.2.1 Setting the Machine Covers

250 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02

4.2.1.2

4.2.1.2 Setting the Cover Guidance

Setting the Cover Guidance

4.2.1.3

4.2.1.3 Checking the Loss Protection

Checking the Loss Protection

Cover guidance (example of SX2 shown)

The cover guidance transitions must be set when the

gantry changer doors are closed, so that the guidances

are flush with one another. Make sure that there is no pro-

truding edge, against which the cover guide roller could

be knocked.

► (1) Check if the loss protection [03103501-xx] is pre-

sent at the top.

► (2) Check if the plastic washer [00201148Sxx] and

the loss protection [03103501-xx] are still present at

the bottom.

► See also the Technical Information "New stopper on

folding covers for SIPLACE SX1 / DX1" [DE: TI2014-

04D05] [EN: TI2014-04E05].

Settings

4.2.1 Setting the Machine Covers Settings on the Basic Machine

Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 251

4.2.1.4

4.2.1.4 Setting the Cover Switch

Setting the Cover Switch

Cover switch (using example of SX2)

Cover switch [03055262-xx]

► Loosen the screws fastening the cover switch, the

centering device and the actuator, so that the assem-

blies can be easily moved.

CAUTION

Screws on actuator

With enforcement of the Machinery Directive DIN EN 1088 (2009), the following has been ex-

ecuted to avoid misuse (e.g. putting the safety features out of action): the actuator and machine

protective switch screws have been replaced by Torx screws with pins. The relevant set of tools

may only be used for performing repair work.

Cover switch (using example of SX2)

► Close the cover far enough for the actuator to be just

over the switch. Align them so that the metal bracket

is parallel to the opening in the switch. The metal

bracket may not scrape against the cover switch.

► Tighten the cover switch screws in this position.