00196497-07_SM_SXDX12_en - 第272页

Settings Nozzle Changer Setting 4.5.3 Jumpers on the Nozzle Change r 272 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 4.5.3 4 . 5 . 3 J u m p e r s o n t h e N o z z le C h a n g e r Jumpers on the Nozzle Changer Overview…

Settings

4.5.1 Setting the Nozzle Changer Height (DLM, C&P20, CPP, TH) Nozzle Changer Setting

Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 271

4.5

4.5 Nozzle Changer Setting

Nozzle Changer Setting

4.5.1

4.5.1 Setting the Nozzle Changer Height (DLM, C&P20, CPP, TH)

Setting the Nozzle Changer Height (DLM, C&P20, CPP, TH)

Parts, equipment and tools

▪ NC shim plate [03021079-xx]

▪ NC support plate [03021044-xx]

▪ Screws DIN 965-M4 x 10-4.8 [00095312-xx]

Setting

4.5.2

4.5.2 Setting the Height of the Nozzle Reject Station (DLM, C&P20, CPP)

Setting the Height of the Nozzle Reject Station (DLM, C&P20, CPP)

Parts, equipment and tools

▪ Shim plates for nozzle reject device [03039514-xx]

Setting

► The distance (1) between the contact surface of the

reject unit and the guide rail of the gantry needs to be

199.8 +/-0.2 mm.

You may need to use shim plates to adjust this.

► The distance (1) between the contact surface of the

nozzle reject station and the guide rail of the gantry

needs to be 189 +0.1/-0.3 mm.

You may need to use shim plates to adjust this.

Settings

Nozzle Changer Setting 4.5.3 Jumpers on the Nozzle Changer

272 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02

4.5.3

4.5.3 Jumpers on the Nozzle Changer

Jumpers on the Nozzle Changer

Overview

Preparation

1. Jumper X10

The jumper X10 needs to be set at the following nozzle

changers:

▪ Nozzle changer basic structure CPx/all assembly -

short [03103649-xx]

▪ Nozzle changer basic structure CPx/all assembly -

long [03103514-xx]

NOTICE

Before installation

Due to the design, this setting must be performed before installation in the machine.

► If the new nozzle changer is being fitted as a spare part in a machine with I/O module con-

trol, you will need to reconnect the jumper to pin 1-2.

To check whether the machine has I/O module control,

proceed as follows:

► Switch over to the operator level Service.

► Select the button.

► Select the button Embedded Software.

► Select the button Update Subsystem.

► If I/O module control is present, you will see the entry

Nozzle Changer at I/O Module.

Settings

4.5.3 Jumpers on the Nozzle Changer Nozzle Changer Setting

Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 273

Setting

► Set the correct value on the jumper for your head type, software and control method.

Nozzle Changer CP20P - Jumper X10

Jumper X10