00196497-07_SM_SXDX12_en - 第71页
Service Work Conveyor 3.3.2 Replacing the I/O Control Unit [03116049-xx] Control Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 71 Removal ► Take a note of the component co unte r reading at the software us er interfa ce. ►…
Service Work Conveyor
Control 3.3.2 Replacing the I/O Control Unit [03116049-xx]
70 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.3.2
3.3.2 Replacing the I/O Control Unit [03116049-xx]
Replacing the I/O Control Unit [03116049-xx]
Parts, Equipment and Tools
▪ I/O control unit II [03116049-xx]
(replaces: I/O control unit [03052315-xx])
Overview
Installation position of I/O control unit
The I/O control unit is located under the cover (1), on the
right when viewed in the direction of transport.
I/O control unit II [03116049-xx]
I/O control unit
See the board description: "5.1.3 I/O control unit
[03116049-xx]" [ ➙ 303]
Service Work Conveyor
3.3.2 Replacing the I/O Control Unit [03116049-xx] Control
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 71
Removal
► Take a note of the component counter reading at the software user interface.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
► Unplug all press-fit connections. You may want to mark the positions, to make clear assignment eas-
ier later on.
► Pull the I/O control unit out of its mount.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
CAUTION
Installation instructions
► Make sure that the DIP switches are configured correctly (see "5.1.3 I/O control unit
[03116049-xx]" [ ➙ 303]).
► Check if the component counter of the software still matches the value you have written
down. If this is not the case, contact SIPLACE service.
Service Work Conveyor
Control 3.3.3 Replacing the Control Computer BoxPC
72 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.3.3
3.3.3 Replacing the Control Computer BoxPC
Replacing the Control Computer BoxPC
Parts, Equipment and Tools
▪ Machines Up To Serial Number Mxxx:
– BoxPC 627B with hotlink cable [03084494-xx] or
– Control Computer BoxPC 627C [03094731Sxx] (station computer and 3D Coplan option)
▪ Machines from Serial Number N001:
– BoxPC ABP402-A CPU1020E 2xPCI SSD-80GB [03120423-xx] (iBase)
1)
Please note that the new CAN card may need a new driver. Observe the instructions in section "4.3.4
Installing the CAN Card Driver" [ ➙ 258].
▪ Installation Manual Windows Embedded Standard 7 [00197737-xx]
Overview
NOTICE
Additional hardware for the BoxPC
The BoxPC is supplied without the following parts. If required, these must be removed from the
old BoxPC and fitted in the new one or ordered as new parts:
DX1/DX2,
SX1/SX2 up to Mxxx
SX1/SX2 from N001
Hotlink Interface PCI-A24-K01 [03052135-xx]
Hotlink interface/Power cable [03042074-xx]
CAN card CAN card PowerCAN-
PCI [03079973-xx]
1)
(replaces:
03052590-xx])
The CAN interface CINX takes over this task (see
Replacing the CAN Interface CINX [03108598-xx]
(from machine no.: N001))
RAM See "3.3.7 Replacing the RAM in the BoxPC" [ ➙ 80]
Ethernet adapter Permanently installed Permanently installed
If a 3D Coplan or a barcode scanner is installed, the
"LAN card PCI Gigabit SEMPRE NC1000-1"
[03112190-xx] is needed in addition.
The BoxPC (1) can be found at the top right of location 2.