00196497-07_SM_SXDX12_en - 第91页
Service Work Conveyor 3.4.6 Replacing the Sensor Interface [03060962-xx] Gantries Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 91 3.4.6 3 . 4 . 6 R e p la c in g t h e S e n s o r I n t e r f a c e [ 0 3 0 6 0 9 6 2 - x x…
Service Work Conveyor
Gantries 3.4.5 Replacing the Gantry Interface Y [03065335-xx]
90 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.4.5
3.4.5 Replacing the Gantry InterfaceY [03065335-xx]
Replacing the Gantry Interface Y [03065335-xx]
Parts, equipment and tools
▪ Gantry interface Y [03065335-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
► Unplug the pneumatic hoses which lead away from the gantry interface.
► Remove the covers above the board. Depending on the version the top cover is secured with press
studs or screws.
► Unplug the electrical connections on the top of the gantry interface. You may want to mark their po-
sitions, to make clear assignment easier later on.
► Loosen the two screws fastening the cover under the gantry interface.
► Unplug the electrical connections on the underside of the gantry interface. You may want to mark
their positions, to make clear assignment easier later on.
► Loosen the two screws fastening the gantry interface and remove the interface from the machine.
Installation
► Follow the removal instructions in reverse order for installation.
1. Gantry interface Y
2. Cover
3. Pneumatic hoses
Service Work Conveyor
3.4.6 Replacing the Sensor Interface [03060962-xx] Gantries
Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02 91
3.4.6
3.4.6 Replacing the Sensor Interface [03060962-xx]
Replacing the Sensor Interface [03060962-xx]
Parts, Equipment and Tools
▪ Sensor interface [03060962-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 13].
► Loosen the two screws fastening the cover plate.
► Unplug the electrical connections to the sensor interface. You may want to mark their positions, to
make clear assignment easier later on.
► Loosen the screws fastening the sensor interface mount.
► Loosen the screws fastening the sensor interface to the mount and remove the sensor interface.
Installation
► Follow the removal instructions in reverse order for installation.
The sensor interface is on the underside of the gantry,
behind a cover.
1. Screws fastening the cover above the sensor inter-
face
(the cover has already been removed in the diagram).
2. Sensor interface
Service Work Conveyor
Gantries 3.4.7 Replacing the Head Interface [03055072-xx]
92 Service Manual SIPLACE SX1/SX2/DX1/DX2 FS02
3.4.7
3.4.7 Replacing the Head Interface [03055072-xx]
Replacing the Head Interface [03055072-xx]
Parts, Equipment and Tools
▪ MODULE/head interface C700B [03055072-xx]
Overview
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section What To Do Before Starting Servicing Work....
► If there is a cover above the boards, dismantle it.
► Unplug all connectors and cable ties on the head interface. You may want to mark their positions, to
make clear assignment or replacement easier later on.
► Dismantle the sensor module. To do this, undo the four fastening screws and the cable holder. Some
versions may include a protective sheet, which is also held with these screws.
► Remove the six screws and the cable holder on the head interface.
► Carefully pull the head interface towards the front. Make sure that the connectors on the head adapt-
er are not damaged.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following instruc-
tions:
NOTICE
C&P20 P
If you are converting to a C&P20 P, one prerequisite is function state -05 or higher for the head
interface.
► You find a complete list of the prerequisites in section Replacing the C&P20 P Head.
Boards on the Gantry
1. Vision board spread spectrum
2. Head adapter (here the version for the TwinHead with
two HCUs)
3. HCU
4. Head interface
5. Sensor module
CAUTION
Installation instructions
► Check the setting of the DIP switch.
(See "5.2.1 Head Interface C700B [03055072-xx]" [ ➙ 311])