TRS GEM Manual for Intel Ver 1.1 - 第131页
GEM Manual for DEK P rinters Event Messages Issue 1.1 March 20th, 2014 Page 131 of 152 Page 131 of 152 EVENT - CEID DESCRIPTION 31233 Alignment out of rang e. 31417 Comms error. 31303 Barcode read failure. 31304 Barcode …
GEM Manual for DEK Printers Event Messages
Issue 1.1 March 20th, 2014 Page 130 of 152 Page 130 of 152
9.6 Alarm Events
EVENT - CEID
DESCRIPTION
31253
Cover opened.
31254
Cover closed.
31314
Head left partly open.
31315
Head moved to safe state.
9.7 Spooling Events
EVENT - CEID
DESCRIPTION
31453
Spooling activated.
31454
Spooling deactivated.
31455
Spool transmission failure.
9.8 Equipment Error Events
EVENT - CEID
DESCRIPTION
10003
System power down.
31201
Pneumatic power down.
31202
Front squeegee error.
31203
Rear squeegee error.
31204
Rising table error.
31205
Print carriage error.
31206
Paste carriage error.
31207
Camera X axis error.
31208
Camera Y axis error.
31209
Rail width error.
31210
Screen XF error.
31211
Screen XR error.
31212
Screen Y error.
31213
Paste cartridge tilt error.
31214
Screen changer drive error.
31215
Board stop stuck.
31216
Board clamp stuck.
31217
Board stuck in rails.
31218
Unable to find fiducial.
31219
Rail lifted error.
31220
Print pressure error.
31221
File error.
31222
Unable to recover.
31223
Recovery started.
31224
Recovered.
31225
Upline transfer error.
31226
Downline transfer error.
31227
Dual shuttle fault.
31230
Screen changer fault.
31232
Lid bolt fault.
GEM Manual for DEK Printers Event Messages
Issue 1.1 March 20th, 2014 Page 131 of 152 Page 131 of 152
EVENT - CEID
DESCRIPTION
31233
Alignment out of range.
31417
Comms error.
31303
Barcode read failure.
31304
Barcode mismatch.
31305
Screen couplings failed.
31306
Motion control timeout.
31307
Camera X failed to position.
31308
Camera Y failed to position.
31309
Stencil aperture blocked.
31310
Stencil smeared.
31311
Paste on pad inspection error.
31312
Bridging detected by inspection system.
31313
Alignment error detected by inspection system.
31321
Event log disk file full.
31322
Proflow error.
31340
CAN node down.
31341
CAN node recovered.
31342
CAN bus down.
31433
CAN bus recovered.
31460
Volume alarm.
40006
Dongle error.
40028
Roll Height Monitor failed
40043
Knead pressure error (front)
40044
Knead pressure error (rear)
40045
Print pressure error (front)
40046
Print pressure error (rear)
40047
Servo following error
40048
Board fiducial 1 not found
40049
Board fiducial 2 not found
40050
Board fiducial 3 not found
40051
Screen fiducial 1 not found
40052
Screen fiducial 2 not found
40053
Screen fiducial 3 not found
40054
Select mark not found
40056
Bad tooling vacuum
40146
Cleaner detached from camera
40147
Recovered cleaner detached from camera
40150
Ball escape detected
40152
Verification item failed (see DVID 2034)
40157
Product ID verification failed
40300
Advanced Adjust Entered
40320
Cleaner Vacuum Sense Error
9.9 Equipment Specific Information Events
EVENT - CEID
DESCRIPTION
10002
System power on.
GEM Manual for DEK Printers Event Messages
Issue 1.1 March 20th, 2014 Page 132 of 152 Page 132 of 152
31251
Line power on.
31255
Printer ready.
31256
Head raised.
31257
Head closed.
31260
Cycle aborted.
31261
Cycle completed.
31262
Cleaning screen.
31263
Parameter adjusted. (See Appendix A)
31264
Setup started.
31272
Setup ended.
31273
Start print cycle.
31275
End print cycle.
31277
Board printed.
31278
Operator log on.
31279
Operator log off.
31280
Clear batch count.
31281
Start maintenance.
31282
End maintenance.
31283
Pressure recalibrated.
31284
Offset recalibrated.
31285
X,Y scale recalibrated.
31286
Theta recalibrated.
31287
Configuration change.
31288
Start diagnostics.
31289
End diagnostics.
31291
Camera reference reset.
31293
Vision height reset.
31294
Print height reset.
31296
Software updated.
31297
New event log.
31301
No cleaner paper.
31302
No cleaner solvent.
31316
Inspection cycle complete.
31317
Clock change request.
31318
Clock changed.
31345
Configuration Parameter modified (with change details – see section 9.15)
31347
Adjust Parameter modified (with change details – see section 9.15)
31457
Remote barcode received.
40004
Evaluation dongle detected.
40005
Valid dongle detected.
40007
Dongle changed.
40008
Front print speed.
40009
Rear print speed.
40020
Maintenance monitoring initialised
40021
Monthly service due
40022
Six monthly service due
40023
Yearly service due
40029
Paste roll height monitoring abandoned