CP43操作手册.pdf.pdf - 第102页
Chapter 4 Device Check Part 2 4.2 Setting Proper Data T o carry out device check it is necessary to set the following Proper data items. 70: Device Check SW No: Parts: Miss: Error This item determines whether or not a ma…
Chapter 4 Device CheckPart 2
1. When the device check function is not used
In this case production becomes possible with the device table
in question when the switch is set to "COMPLETE." The signal
tower on the rear fence will begin flashing.
On the other hand, if the switch is set to "CANCEL" then
production with the device table in question will not be
possible. The signal tower on the rear fence will be lit.
2. When the device check function is used
In this case when all devices have been checked and the switch
is set to "COMPLETE", production becomes possible and the
device table moves from its resupply position to its part
picking position.
If the switch is set to "CANCEL" the machine remains in device
check mode and production with that table is not possible. The
signal tower on the rear fence will be lit.
To operate in the device change mode the status of one of the
tables, either table 1 or table 2, must be ready for production.
Also note that to operate in the changeover mode it is necessary for
the original table to be ready for production.
In the case where operation is not possible because neither table is
ready for production, the message "Parts are unset" will display
and the machine will wait for the [PARTS SET] switch to be set to
"COMPLETE".
2 – 33Version 2.0
FCP IV-3 Operation
Chapter 4 Device CheckPart 2
4.2 Setting Proper Data
To carry out device check it is necessary to set the following Proper data
items.
70: Device Check SW No: Parts: Miss: Error
This item determines whether or not a mandatory device check will
be performed when parts run out and when a program change has
occurred. If this item is set to "No" device check is not carried out
when a program changes.
No : Mandatory device check is not performed.
Parts : Mandatory device check is performed when parts run out.
Miss : Mandatory device check is performed when parts run out or
when parts are mispicked.
Error : Mandatory device check is performed when parts run out,
parts are mispicked or an image processing error occurs.
71: Verifier Tool Non: Barcode: Handy_term
This item specifies the hardware to be used in device check.
Non : Handy terminal is not used.
Barcode : Not supported.
Handy_term : Handy terminal is used (option)
Note: If "Handy_term" is set then a value other than 0 must be set in
Proper data item 72: Barcode Reader Type.
74: ESC Permission Non: Permit
This item determines whether or not the [ESC] command will be
enabled during device check. The [ESC] command allows the user to
escape from setting all devices.
Non : [ESC] command is disabled.
Permit : [ESC] command is enabled.
75: MAN Permission Non: Permit
This item determines whether or not it is possible to input data from
the handy terminal numerical keypad to the operation panel on the
machine.
Non : Numerical keypad is disabled.
Permit : Numerical keypad is enabled.
If this item is set to "Permit" the numerical keypad and [CR] key on
the operation panel are also enabled.
2 – 34Version 5.0
FCP IV-3 Operation
Chapter 4 Device CheckPart 2
4.3 Carrying Out Device Check
When device check is carried out the following operation screen displays.
The meaning of each item that displays is explained below.
(a) Device number
(b) Status of parts
Un Set (yellow) : device has not yet been checked
OK (green) : device has been set
(blue) : device was used in previous program but is not
going to be used in the coming program.
Next D : next device is not yet set
Tape E (white) : end of tape detected
Parts E (red) : feeder is out of parts
Pickup (highlighted in yellow) : parts mispicked
Vision (purple) : vision processing error
(c) Number of parts used per board.
(d) Device comment
As shown in the above figure there are 3 types of display modes for
device check.
F1: MODE 0
In this mode the display screen will be the same as the one in the
figure above where 10 consecutive device positions display whether
the device position is used or not.
Page 451
MODE 1 MODE 2 MODE 3 RETURN
D001
D002
D003
D004
D005
D006
D007
D008
D009
D010
Un Set
Parts E
Vision
Tape E
Next_d
Pickup
[0013]
[0008]
[0002]
[0000]
[0001]
[0005]
[0007]
[0002]
[0003]
[0015]
Device_comment_No_1
Korewa_No_2Desu
PCPR1-2TL
MSD2HD256
Micro_Tr_No1
Super_Mini_Tr
Nihongonitute
N3456Sd23
Jaf
(a) (b) (c) (d)
2 – 35Version 5.0
FCP IV-3 Operation