CP43操作手册.pdf.pdf - 第240页

$ ❈ 30: W idth Min Limit ( 0.00 ~ 655.35 ) [mm] = 050.00 $ # 40: LMS Flag = [Off] On $ # 41: Cell Status = [Unit] Active Passive $ # 42: Change Over Mode ( 0 ~ 200 ) = 000 $ # 43: Auto Start = [No] Y es $ # 44: Backup Pl…

Chapter 1 Proper Data ListingPart 4

# 1: ID_Code [8] ASCII CODE = 0

# 2: Language = [English] Japanese French

# 3: Red_Light = 0000 0000 0000 0000

# 4: Yellow_Light = 0000 0000 0000 0000

# 5: Blue_Light = 0000 0000 0000 0000

# 6: Red_Flash = 0000 0000 0000 0000

# 7: Yellow_Flash = 0000 0000 0000 0000

# 8: Blue_Flash = 0000 0000 0000 0000

$# 9: User_Define A = 0000 0000 0000 0000

❈ 11: Machine_Status A = 0000 0000 0000 0000

❈ 12: Machine_Status B = 0000 0000 0000 0000

❈ 13: Machine_ID = 0000 0000 0000 0000

# 14: PCB_Location = [Corner] Pin

$ 20: Loader Status A = 0000 0000 0000 0000

$ 21: Loader Status B = 0000 0000 0000 0000

$ 22: Conveyor Type = [L->R] R->L

$ 23: Wait Signal = [Off] On

$# 24: Busy Invalid = [No] Yes

$# 25: Conveyor Control = [Manu] Auto

$# 26: Conveyor Adj. Limit ( 0.05 ~ 1.00 ) [mm] = 0.50

$# 27: Conveyor Stop Offset ( 0.00 ~ 2.00 ) [mm] = 0.30

$# 28: Conveyor adj. Timer ( 0 ~ 120000 ) [msec]= 000600

$❈ 29: Width Max Limit ( 0.00 ~ 655.35 ) [mm] = 460.00

4 – 1Version 2.0

DATA NAME

1. Proper Data Listing

The following symbols are used before the Proper data values.

✩: Varies from machine to machine. Must be measured.

❈: Cannot be changed by the user.

#: Can be changed by the user.

@: Machine automatically changes this. (Sometimes the user can also

change this.

$: Not currently in use.

$❈ 30: Width Min Limit ( 0.00 ~ 655.35 ) [mm] = 050.00

$# 40: LMS Flag = [Off] On

$# 41: Cell Status = [Unit] Active Passive

$# 42: Change Over Mode ( 0 ~ 200 ) = 000

$# 43: Auto Start = [No] Yes

$# 44: Backup Plate Check = [No] Yes

$❈ 45: Command Line Status = [RS232C] LAN ETHERNET

$# 46: Command Line Port ( 0 ~ 4 ) = 0

$✳ 47: ID Station Type = [S_type] A_type

$# 48: Buzzer Warning = [On] Off

$# 49: Process Timer ( 1 ~ 120000 ) [msec]= 010000

$# 50: Reader Type ( 0 ~ 9 ) = 0

$# 51: Code Reader Timer ( 1 ~ 120000 ) [msec]= 010000

$# 52: Code Reader Retry ( 0 ~ 10 ) = 00

$# 53: Reader1 Port No. ( 0 ~ 30 ) = 0

$# 54: Reader2 Port No. ( 0 ~ 30 ) = 0

$# 55: PCB Code Terminal = [Non] Use

$ 56: Terminal Type = [CRX1200] VT-100

$# 57: Code Terminal Port ( 0 ~ 30 ) = 0

# 70: Device Check SW =[No] Parts Miss Error

# 71: Verifier Tool = [Non] Barcode Handy_term

# 72: Barcode Reader Type ( 0 ~ 9 ) = 0

# 73: Device Check Port ( 0 ~ 30 ) = 0

# 74: ESC Permission = [Non] Permit

# 75: MAN Permission = [Non] Permit

# 76: HT Comment Term. Code ASCII CODE =

# 77: HT Verify Term. Code ASCII CODE =

# 78: D Change Trigger = Error Parts Miss PD

✩❈ 100: Pickup Position T1 ( 0 ~50000 ) [pulse]= 00000

✩❈ 101: Pickup Position T2 (-50000~0 ) [pulse]= 00000

✩❈ 102: Origin Position Z (-65000~ 65000 ) [pulse]= 00000

DATA NAME

Chapter 1 Proper Data ListingPart 4

4 – 2Version 2.0

Chapter 1 Proper Data ListingPart 4

✩❈ 103: Placing Position X (-100000~ 0 ) [pulse]= 000000

✩❈ 104: Placing Position Y ( 0 ~ 100000 ) [pulse]= 000000

✩❈ 105: Loading Position X (-100000~ 0 ) [pulse]= 000000

✩❈ 106: Loading Position Y (-65000~ 65000 ) [pulse]= 00000

✩❈ 107: Mark Read Position X (-100000~100000 ) [pulse]= 000000

✩❈ 108: Mark Read Position Y ( 0 ~ 100000 ) [pulse]= 000000

✩❈ 109: PCB Check Position X (-100000~100000 ) [pulse]= 000000

✩❈ 110: PCB Check Position Y ( 0 ~ 100000 ) [pulse]= 000000

✩❈ 111: D1 Original Position (-10000~ 10000 ) [pulse]= 000000

✩❈ 112: D2 Original Position (-10000~ 10000 ) [pulse]= 00000

✩❈ 113: Max Limit Position X ( 0 ~ 100000 ) [pulse]= 000000

✩❈ 114: Max Limit Position Y ( 0 ~ 100000 ) [pulse]= 000000

✩❈ 115: Max Limit Position D1 ( 0 ~ 100000 ) [pulse]= 000000

✩❈ 116: Max Limit Position D2 (-10000~ 500000 ) [pulse]= 000000

✩❈ 117: Max Limit Position Z (-65000~ 65000 ) [pulse]= 00000

✩❈ 118: Min Limit Position X (-100000~ 0 ) [pulse]= 000000

✩❈ 119: Min Limit Position Y (-100000~ 0 ) [pulse]= 000000

✩❈ 120: Min Limit Position D1 (-500000~ 10000 ) [pulse]= 000000

✩❈ 121: Min Limit Position D2 (-50000~ 50000 ) [pulse]= 000000

✩❈ 122: Min Limit Position Z (-65000~ 65000 ) [pulse]= 000000

# 130: Nozzle Check SW = [No] Yes

❈ 131: Narrow View Camera = [Non] Use

❈ 132: Front Light = [Non] Use

# 133: Cam Speed ( 0 ~ 100.0 ) [%] = 000.0

# 134: Skip Number ( 0 ~ 16 ) = 0

# 135: Skip Nozzle S ( 0 ~ 12 ) = 0

# 136: Skip Nozzle M ( 0 ~ 12 ) = 0

# 137: Skip Nozzle L ( 0 ~ 12 ) = 0

$ 138: M/C Size = [4000] 5000

4 – 3Version 2.0

DATA NAME