CP43操作手册.pdf.pdf - 第3页

Contents Contents Introduction ...........................................................................................ix Part One, Machine Operation 1. Description of the Machine .....................................…

100%1 / 364
Notice
1. All rights regarding this manual are reserved by Fuji Machine Manufacturing Co., Ltd. This
manual may not, in whole or in part, be reproduced by any means (electronic, mechanical or
otherwise), or reused in any way, without the prior written permission of Fuji Machine
Manufacturing Co., Ltd.
2. Fuji Machine Manufacturing Co., Ltd. accepts no responsibility for any situations that may arise as
a result of the use of this manual.
3. Fuji Machine Manufacturing Co., Ltd. reserves the right to change the content of this manual
without notice.
4. Every effort has been made to ensure that this manual is correct in every detail. However, please
contact Fuji in the unlikely event that errors or omissions are detected.
Copyright 1999 by Fuji Machine Manufacturing Co., Ltd.
All Rights Reserved.
Fuji Machine Manufacturing Co., Ltd. serves its customers from the following locations:
Fuji Machine Manufacturing Co., Ltd.
19 Chausuyama Yamamachi
Chiryu, Aichi Prefecture, 472-8686 Tel : 0566-81-2111
Japan Fax : 0566-83-1140
Fuji America Corporation
171 Corporate Woods Parkway
Vernon Hills, IL. 60061 Tel : 847-913-0162
USA Fax : 847-913-0186
Fuji Machine Mfg (Europe) GmbH
Peter-Sander-Str. 43
D-55252 Mainz-Kastel Tel : 06134-202120
Germany Fax : 06134-202200
Fuji Singapore Office
C/O Mecomb Singapore Limited
Sime Darby Centre
896 Dunearn Road #04-03A, Tel : 4675952
Singapore 589472 Fax : 4693758
Fuji Malaysia Office
C/O Mecomb Malaysia Sdn Bhd
2487, Jalan Sultan Azlan Shah Tel : 604-656-4002
11700 Penang, Malaysia Fax : 604-656-2941
Fuji do Brasil Maquinas Industriais Ltda.
Rua Joao Cachoeira, 128
Itaim Bibi, Sao Paulo, SP
04535-000 Tel : 11-3064-7650
Brazil Fax : 11-852-6833
Latest Version 1.0
Contents
Contents
Introduction ...........................................................................................ix
Part One, Machine Operation
1. Description of the Machine..........................................................1–1
2. Operation of the Keys...................................................................1–3
2.1 The Function Keys....................................................................................1–3
2.2 Inching Keys.............................................................................................1–4
2.3 Numerical Input Keys................................................................................1–6
2.4 Buttons......................................................................................................1–7
2.4.1 Buttons on the Front Panel............................................................1–7
2.4.2 Rear Operation Panel....................................................................1–8
3. Starting and Shutting Down.......................................................1–11
3.1 Startup ....................................................................................................1–11
3.1.1 Normal Operation........................................................................1–11
3.1.2 Reset-Start..................................................................................1–14
3.1.3 I/O Check Start............................................................................1–15
3.1.4 Trace List Printout .......................................................................1–15
3.2 Shutting Down ........................................................................................1–16
4. The Display..................................................................................1–17
4.1 CRT Display Monitor...............................................................................1–17
4.2 First Display Area ...................................................................................1–20
4.2.1 Display During Automatic Operation Mode.................................1–20
4.2.2 Display When Not In Automatic Operation..................................1–24
4.3 Second Display Area..............................................................................1–25
4.3.1 Emergency Stop..........................................................................1–28
4.3.2 Cycle Stop (During Automatic Operation)...................................1–29
4.3.3 Other Interruptions During Automatic Operation.........................1–30
4.3.4 Press START...............................................................................1–31
4.3.5 When the Machine Cannot Run..................................................1–31
4.3.6 Device Table Information in Device Changeover Mode ..............1–32
iVersion 5.0
FCP IV-3 Operation
FCP IV-3 Operation
Contents
5. Zero Setting.................................................................................1–33
6. Basic Operation ..........................................................................1–35
6.1 Definition of Coordinates ........................................................................1–35
6.2 Definition of Parts ...................................................................................1–35
6.2.1 Definition of Device Tables..........................................................1–35
6.2.2 Original Table ..............................................................................1–35
6.2.3 Definition of Device Numbers......................................................1–36
6.2.4 Functions of Each Station ...........................................................1–37
6.2.5 Parts of the Board Loader System..............................................1–39
6.3 Changing the Original Table ...................................................................1–40
6.3.1 Change Due to Change of Production Program..........................1–40
6.3.2 Change Due to Change of Table Mode.......................................1–41
6.4 Device Tables: Part Pickup Position and Resupply Position ..................1–41
6.4.1 Conditions for Moving to the Part Pickup Position ......................1–42
6.4.2 Conditions for Moving to the Resupply Position..........................1–42
6.5 Shutter Operation ...................................................................................1–42
6.6 XY Table Height Adjustment...................................................................1–43
6.7 Parts Supply Position..............................................................................1–43
6.7.1 Joint Mode...................................................................................1–43
6.7.2 Device Change Mode..................................................................1–44
6.7.3 Changeover Mode.......................................................................1–44
6.8 Discarding Picked Parts..........................................................................1–45
7. Nozzle Center Measurement......................................................1–47
7.1 An Explanation of Nozzle Center Measurement.....................................1–47
7.2 Main Points.............................................................................................1–49
7.3 Necessary Data......................................................................................1–50
7.4 Procedure...............................................................................................1–51
7.5 Setting the Maximum Nozzle Bend Tolerance........................................1–51
7.6 Setting the Nozzle Background Disk Diameter.......................................1–53
7.7 Skipping a Faulty Nozzle.........................................................................1-54
iiVersion 5.0