DEUKYX-193-4110_G5S2_VOL4 - 第145页
DEUKYX 2-5 193-41 10 2.2 Management-Informationsliste Code Anzeigebereich A Anzeigebereich B 10d01 Pattern program is abnormal Please set the normal pattern program 10e01 Prod Chng is not ready Conveyor width does not t…
DEUKYX
2-4193-4110
2.2 Management-Informationsliste
2.2 Management-Informationsliste
Nachfolgend nden Sie eine Liste der Management-Informationen sortiert nach
Fehlercodes.
Code Anzeigebereich A Anzeigebereich B
10101 Emergency Stop Press [POWER ON] button to activate Load Power circuit.
10103 Emergency Stop Emergency Stop switch is pressed. Please cancel it.
10201 Air Pressure Drop Air Pressure Drop is detected
10401
Safety cover lock
conrm
Please close and lock the safety cover.
10402
Safety cover lock
conrm
Operate it after close and lock the safety cover.
10403
Safety cover lock
conrm
Operate after close and lock the safety cover.
10404
Safety cover lock
conrm
The safety cover is in unlock. Please complete to unlock and operate it.
10503
Beam XY main circuit
OFF
Beam XY main circuit Error
10801
Feeder base conrm
(Block1)
Set the feeder cart (Block1) and connect cable.
10802
Feeder base conrm
(Block1)
Cannot set Feeder Cart downward to detect Elevator Unit (Block1). Operate
after remove it .
10803
Feeder base conrm
(Block1)
Elevator Unit (Block1) is not connected. Please connect to it with "Unit
Exchange Menu".
10804
Feeder base conrm
(Block1)
Batch Connector of Elevator Unit (Block1) is not connected. Please check
connection.
10805
Feeder base conrm
(Block1)
Feeder cart (Block1) is not upper position. Push Feeder Ready Switch.
10806
Feeder base conrm
(Block1)
Push Feeder Ready SW.
10807
Feeder base conrm
(Block1)
Feeder base power or Feeder power is "OFF". Please press "Feeder Ready"
switch (Block1), and put it up again after putting Feeder Cart (Block1) down.
10901
Feeder base conrm
(Block2)
Set the feeder cart and connect cable. (Block2)
10902
Feeder base conrm
(Block2)
Cannot set Feeder Cart downward to detect Elevator Unit (Block2). Operate
after remove it.
10903
Feeder base conrm
(Block2)
Elevator Unit (Block2) is not connected. Please connect to it with "Unit
Exchange Menu".
10904
Feeder base conrm
(Block2)
Batch Connector of Elevator Unit (Block2) is not connected. Please check
connection.
10905
Feeder base conrm
(Block2)
Feeder cart (Block2) is not upper position. Push feeder ready sw.
10906
Feeder base conrm
(Block2)
Push feeder ready sw.
10907
Feeder base conrm
(Block2)
Feeder base power or Feeder power is "OFF". Please press "Feeder Ready"
switch (Block2), and put it up again after putting Feeder Cart (Block2) down.
10b01
Feeder is not ready
(Block1)
Please turn on the Feeder Ready SW (Block1).
10c01
Feeder is not ready
(Block2)
Please turn on the Feeder Ready SW (Block2).
DEUKYX
2-5193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
10d01
Pattern program is
abnormal
Please set the normal pattern program
10e01 Prod Chng is not ready Conveyor width does not t production data. Execute conveyor width setup.
11001 Empty Feeder (Block1) Please set the feeder (Block1) that used by the pattern program.
11101 Empty Feeder (Block2) Please set the feeder (Block2) that used by the pattern program.
11201
Stock Stick Feeder
(Block1)
A setup of a stock stick unit and part library data is not in agreement. Please
carry that whose discernment ID of a part library / supply data and ID on the
rear surface of a unit correspond.
11202
Stock Stick Feeder
(Block1)
Please check the value of the thickness data t and Ut of a part library.
11301
Stock Stick Feeder
(Block2)
A setup of a stock stick unit and part library data is not in agreement. Please
carry that whose discernment ID of a part library / supply data and ID on the
rear surface of a unit correspond.
11302
Stock Stick Feeder
(Block2)
Please check the value of the thickness data t and Ut of a part library.
11401 Zeroing not nish Perform All zeroing
11402 Zeroing not nish Perform All zeroing
11403 Zeroing not nish Perform All zeroing
11404 Zeroing not nish Perform All zeroing
11405 Zeroing not nish Perform All zeroing
11406 Zeroing not nish Motor is not servo on. Perform All zeroing
11701 PCB positioning Please position the PCB.
11702 PCB positioning Set Pos PCB [Output Position].
11703 PCB positioning Set Pos PCB [Input Position].
11704 PCB positioning Please cancel PCB positioning after cancelling operation.
11705 PCB positioning Please set PCB positioning [Input or Output] of [Lane A]
11706 PCB positioning Please set PCB positioning. [Output position] of [Lane A].
11707 PCB positioning Please set PCB positioning [Input position] of [Lane A].
11708 PCB positioning Please set PCB Positioning [Input or Output] of [Lane B].
11709 PCB positioning Please set PCB Positioning [Output position] of [Lane B].
1170a PCB positioning Please set PCB positioning [Input position] of [Lane B].
1170b PCB positioning Please set PCB positioning of input position on PCB transfer menu.
1170c PCB positioning Please set PCB positioning of [Lane A] input position on PCB transfer menu.
1170d PCB positioning Please set PCB positioning of [Lane B] input position on PCB transfer menu.
1170e PCB positioning
Board has been positioned inside the unit two. For nishing, please run it from
an upstream position positioning sequentially one by one.
11901
Head unsettled comp.
conrmation
An unsettled component was detected. Please discard the component. In case
of the "Pauses" condition, perform the operation for interruption.
11a01
Nozzle stocker lower
limit conrmation
Please perform All zeroing.
11c01
Nozzle arrangement
conrmation
The nozzle arrangement of the Current Program differs from it of Head.
DEUKYX
2-6193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
11c02
Nozzle arrangement
conrmation
A nozzle cannot be stored. Please check the following. (Block 1)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Conguration Data
11c03
Nozzle arrangement
conrmation
A nozzle cannot be stored. Please check the following. (Block 2)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Conguration Data
11c04
Nozzle arrangement
conrmation
The nozzles to be used are insufcient. Please check the following. (Block 1)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Conguration Data
11c05
Nozzle arrangement
conrmation
The nozzles to be used are insufcient. Please check the following. (Block 2)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Conguration Data
11c06
Nozzle arrangement
conrmation
The nozzle placement of the head to assist for is different. (Head2)
11c07
Nozzle arrangement
conrmation
The nozzle placement of the head to assist for is different. (Head1)
11c08
Nozzle arrangement
conrmation
The Nozzle used is insufcient for assist. Please arrange the Nozzle used.
11c09
Nozzle arrangement
conrmation
Nozzle placement of Nozzle Stocker is short, the sequence that cannot change
a nozzle for exists. Please conrm nozzle stocker placement.
11c0a
Nozzle arrangement
conrmation
A nozzle exists on Nozzle Stocker, but the sequence that cannot change a
nozzle for by the limitation of the head exists. Please conrm nozzle stocker
placement.
12a01
Tray shortage Comp
(Block1)
Please supply Tray Cmpnt, close Tray Safety door and push Tray Ready SW
(Block1).
12a02
Tray shortage Comp
(Block1)
There is the shortage components. Please supply the components.
12b01
Tray shortage Comp
(Block2)
Please supply Tray Cmpnt, close Tray Safety door and push Tray Ready SW
(Block2).
12b02
Tray shortage Comp
(Block2)
There is the shortage components. Please supply the components.
12c01
Tray is not ready
(Block1)
Error signal of the unit is detected.\r\n(1) Please supply the components. (2)
Please close elevator loading door.\r\n(3) Please press a reset button. (4)
Please release Inhibit button.
12d01
Tray is not ready
(Block2)
Error signal of the unit is detected.\r\n(1) Please supply the components. (2)
Please close elevator loading door.\r\n(3) Please press a reset button. (4)
Please release Inhibit button.
13101 Feeder set Err
A pickup miss comp is detected. (Block1) Please open the safety door and
conrm whether pickup miss comp is dropped. If the comp is dropped, there is
a possibility of interference with Head. A detection state can be checked on a
control screen.
13102 Feeder set Err
The feeder latch worked off. (Block1)
Please close the hook of a feeder. A detection state can be checked on a
control screen.
13103 Feeder set Err
A pickup miss comp is detected. (Block2) Please open the safety door and
conrm whether pickup miss comp is dropped. If the comp is dropped, there is
a possibility of interference with Head. A detection state can be checked on a
control screen.
13104 Feeder set Err
Feeder Latch worked off. (Block2)
Please close the hook of a feeder. A detection state can be checked on a
control screen.
13105 Feeder set Err Not connect selected Feeder.