DEUKYX-193-4110_G5S2_VOL4 - 第150页

DEUKYX 2-10 193-41 10 2.2 Management-Informationsliste Code Anzeigebereich A Anzeigebereich B 18001 Recycling Conveyor (Block1) Recycle Conveyor (Block1) is lled up. 18002 Recycling Conveyor (Block1) The connection of R…

100%1 / 386
DEUKYX
2-9193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
16005 Tray teaching The component is not drawn out (Block2). Draw out the component.
16101 Coplanarity Teaching
"Coplanarity Detection" of Test Operation Mode is set "No". Execute it after
cancelling Test Operation Mode.
16201 Coplanarity Test Please pickup part.
17009
Teaching Check on the
position of Glass jig
Not found Glass Jig for Teaching. Please check that Glass Jig is set in its
position.
17201 Nozzle set-up (Block1)
Nozzle Placement/Store mode of Stocker (Block2) is not possible to operate.
Please specify Stocker (Block1).
17202 Nozzle set-up (Block1)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
17203 Nozzle set-up (Block1)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
17204 Nozzle set-up (Block1)
Because of interference with Nozzle which is already placed, it cannot be
placed. Do not place Nozzle in the front and rear of two Odd nozzle placed.
17205 Nozzle set-up (Block1) Placement/Store is impossible in the position for the specied stocker.
17206 Nozzle set-up (Block1)
It is impossible to place it because of interfering in the placed nozzle. Please
do not place a nozzle before or after placing ODD nozzle.
17301 Nozzle set-up (Block2)
Nozzle Placement/Store mode of Stocker (Block1) is not possible. Please set
Stocker (Block2).
17302 Nozzle set-up (Block2)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
17303 Nozzle set-up (Block2)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
17304 Nozzle set-up (Block2)
Because of interference with Nozzle which is already placed, it cannot be
placed. Do not place Nozzle in the front and rear of two Odd nozzle placed.
17305 Nozzle set-up (Block2) Placement/Store is impossible in the position for the specied stocker.
17306 Nozzle set-up (Block2)
It is impossible to place it because of interfering in the placed nozzle. Please
do not place a nozzle before or after placing ODD nozzle.
17401
Button for inserting
power
Can not supply power while Side view camera program is on writing. Operate it
after writing completely.
17501
Operation mode set
conrmation
"Feeder Connection" or "Feeder Serial Communication" of Test Operation
Mode is set. Execute it after reset Operation Mode.
17502
Operation mode set
conrmation
"Component Feed" of Test Operation Mode is set. Execute it after reset
Operation Mode.
17601 Inching movement Perform zeroing.
17602 Inching movement Please push the Feeder Base Ready SW.
17603 Inching movement Close the safety door of Tray, and press the Ready button.
17604 Inching movement The range is out of movable Range.
17605 Inching movement
HL-axis is fallen. There is a possibility of collision between Noz and axis.
Please perform zeroing of HL-axis or move it to origin position.
17606 Inching movement
L1-axis is fallen. There is a possibility of collision between Noz and axis.
Please perform zeroing of L1-axis or move it to origin position.
17607 Inching movement
L2-axis is fallen. There is a possibility of collision between Noz and axis.
Please perform zeroing of L2-axis or move it to origin position.
17608 Inching movement
L3-axis is fallen. There is a possibility of collision between Noz and axis.
Please perform zeroing of L3-axis or move it to origin position.
17701 Zeroing (set axis) Push Ready SW of Feeder Base.
17702 Zeroing (set axis) Close the safety door of Tray, and press the Ready button.
DEUKYX
2-10193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
18001
Recycling Conveyor
(Block1)
Recycle Conveyor (Block1) is lled up.
18002
Recycling Conveyor
(Block1)
The connection of Recycling Conveyor (Block1) differs from Cmpnt Arranging
Data. Or, it has multi-connection.
18003
Recycling Conveyor
(Block1)
Recycling Conveyor (Block1) is on ready. Please remove parts and resume
production after completion of operation.
18004
Recycling Conveyor
(Block1)
Recycling conveyer is connected to F159. Please be connected to the range of
F105-F157 or F205-F257 again.
18101
Recycling Conveyor
(Block2)
Recycling Conveyor (Block2) is lled up.
18102
Recycling Conveyor
(Block2)
The connection of Recycling Conveyor (Block2) differs from Cmpnt Arranging
Data. Or, it has multi-connection.
18103
Recycling Conveyor
(Block2)
Recycling Conveyor (Block2) is on ready. Please remove parts and resume
production after completion of operation.
18104
Recycling Conveyor
(Block2)
Recycling conveyer is connected to F259. Please be connected to the range of
F105-F157 or F205-F257 again.
18201 Tray (Block1)
Close the safety door of Tray, and press a button [READY] of it. When Tray
[READY] does not change to [ON], press the button [READY] of Feeder.
18202 Tray (Block1) Pallet of Tray is drawn out. Execute zeroing all, and store the pallet.
18203 Tray (Block1) Tray breaking out was detected. Execute zeroing all, and store the pallet.
18204 Tray (Block1) Press [READY] button of Feeder base, and supply the power of Tray.
18205 Tray (Block1) Close the safety door (Center) of Tray, and press [READY] button.
18206 Tray (Block1) Close the safety door (Lower) of Tray, and press [READY] button.
18207 Tray (Block1) Close the safety door (Upper) of Tray, and press [READY] button.
18208 Tray (Block1) Zeroing of Traverse-axis is not nished. Perform zeroing of Tray.
18209 Tray (Block1) Zeroing of Elevator1-axis is not nished. Perform zeroing of Tray.
1820a Tray (Block1) Zeroing of Elevator2-axis is not nished. Perform zeroing of Tray.
1820b Tray (Block1) Pickup miss cmpnt (8 mm) is detected.[B15417]
1820c Tray (Block1) Pickup miss cmpnt (14 mm) is detected.[B15418]
1820d Tray (Block1) Pickup miss cmpnt (28 mm) is detected.[B15419]
1820e Tray (Block1) Pallet Chuck Claw is open.
1820f Tray (Block1) Pallet Error is detected.
18210 Tray (Block1) Magazine 1 (Lower) Shutter on Traverse side is open.
18211 Tray (Block1) Magazine 2 (Upper) Shutter on Traverse side is open.
18212 Tray (Block1) Access detecting Sensor (Right) : Cannot detect Elevator Unit
18213 Tray (Block1) Access detecting Sensor (Left) : Cannot detect Elevator Unit
18214 Tray (Block1) Pick-up miss cmpnt is detected.
18215 Tray (Block1) Traverse axis is not on origin. Please perform zeroing of Tray.
18216 Tray (Block1) Tray is running. Please operate it after completion.
18217 Tray (Block1) Please supply Tray Cmpnt after all zeroing.
18218 Tray (Block1) The supply area magazine has an unsettled palette. Please remove it.
18219 Tray (Block1) A head and a traverse axis interfere it. Please evacuate in a head.
DEUKYX
2-11193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
18301 Tray (Block2)
Close the safety door of Tray, and press a button [READY] of it. When Tray
[READY] does not change to [ON], press the button [READY] of Feeder.
18302 Tray (Block2) Pallet of Tray is drawn out. Execute zeroing all, and store the pallet.
18303 Tray (Block2) Pallet Error of Tray is detected. Execute zeroing all, and store the pallet.
18304 Tray (Block2) Press [READY] button of Feeder base, and supply the power of Tray.
18305 Tray (Block2) Close the safety door (Center) of Tray, and press [READY] button.
18306 Tray (Block2) Close the safety door (Lower) of Tray, and press [READY] button.
18307 Tray (Block2) Close the safety door (Upper) of Tray, and press [READY] button.
18308 Tray (Block2) Zeroing of Traverse-axis is not nished. Perform zeroing of Tray.
18309 Tray (Block2) Zeroing of Elevator1-axis is not nished. Perform zeroing of Tray.
1830a Tray (Block2) Zeroing of Elevator2-axis is not nished. Perform zeroing of Tray.
1830b Tray (Block2) Pickup miss cmpnt (8 mm) is detected.[B15417]
1830c Tray (Block2) Pickup miss cmpnt (14 mm) is detected.[B15418]
1830d Tray (Block2) Pickup miss cmpnt (28 mm) is detected.[B15419]
1830e Tray (Block2) Pallet Chuck Claw is open.
1830f Tray (Block2) Pallet Error is detected.
18310 Tray (Block2) Magazine1 (Lower) Shutter on Traverse side is open.
18311 Tray (Block2) Magazine2 (Upper) Shutter on Traverse side is open.
18312 Tray (Block2) Access detecting Sensor (Right) : Cannot detect Elevator Unit
18313 Tray (Block2) Access detecting Sensor (Left) : Cannot detect Elevator Unit
18314 Tray (Block2) Pick-up miss cmpnt is detected.
18315 Tray (Block2) Traverse axis is not on origin. Please perform zeroing of Tray.
18316 Tray (Block2) Tray is running. Please operate it after completion.
18317 Tray (Block2) Please supply Tray Cmpnt after all zeroing.
18318 Tray (Block2) The supply area magazine has an unsettled palette. Please remove it.
18319 Tray (Block2) A head and a traverse axis interfere it. Please evacuate in a head.
18401
Tray is not ready to
zeroing (Block1)
Execute all zeroing.
18501
Tray is not ready to
zeroing (Block2)
Execute all zeroing.
18601 Warning of wiring error Vacuum Pump 1CB Error
18602 Warning of wiring error Monitor Error of DC load power
18603 Warning of wiring error Beam 1 CB Error Monitor Error
18604 Warning of wiring error Beam 2 CB Error Monitor Error
18701 Feeder Alternate Illegal alternate setup of pattern program. Check the settings.
18702 Feeder Alternate Invalid feeder in alternating. Set feeder valid
18801 XY Origin Offset
Since the data transfer of XY-Origin offset is not completed, please perform
again after waiting for a while (Beam 1).
18802 XY Origin Offset
Since the data transfer of XY-Origin offset is not completed, please perform
again after waiting for a while (Beam 2).