DEUKYX-193-4110_G5S2_VOL4 - 第161页
DEUKYX 2-21 193-41 10 2.2 Management-Informationsliste Code Anzeigebereich A Anzeigebereich B 0d3204 Feeder Base Up/Down Operation Restrictions (Block1) Please check that Recycle Conveyor is not carried on a feeder base,…
DEUKYX
2-20193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
0d1603
Large nozzle
interference
Operation is impossible because large nozzles are placed in 2 axes adjacent
to the head2. Please take off one of them by hand, and then edit the nozzle
arrangement data.
0d1604
Large nozzle
interference
It cannot run because a large nozzle runs to the interfering position.
0d1701
Non-applied function of
the long board
The function is not applied to PCB which is longer than 610 mm.
0d1801 Transfer conrmation The machine has not stopped.
0d1901 Bowl Feeder
Bowl feeder cart (Block1) has not been set. Please check a type of the cart.
And, Please check the setting for unit exchange screen.
0d1902 Bowl Feeder
Bowl feeder cart (Block2) has not been set. Please check a type of cart. And,
Please check the setting for unit exchange screen.
0d2001
Non-applied function of
backup jig support to
vacuum
The function is not available if backup jig to support vacuum is applied.
0d2101
Independent /
alternation production
mode
The alternation production mode cannot run during an independent production
mode run. Please start again after stopping a machine.
0d2102
Independent /
alternation production
mode
By the state of the PCB in the machine, I do not come in a startup. Please start
again after I remove a PCB, or stopping it.
0d2201 Selection at any time
Please push the abandonment button of the control screen and specify the
place where parts are abandoned. (head1) The parts which have set up “at-
any-time selection” or “after-interlock recovery” are adsorbed states.
0d2202 Selection at any time
Please push the abandonment button of the control screen and specify the
place where parts are abandoned. (head2) The parts which have set up “at-
any-time selection” or “after-interlock recovery” are adsorbed states.
0d2301
Conveyor safety sensor
detection
The conveyor safety sensor (input side) is detected.
0d2302
Conveyor safety sensor
detection
The conveyor safety sensor (output side) is detected.
0d2401
Feeder safety sensor
detection (Block1)
The feeder safety sensor (Block1) is detected.
0d2402
Feeder safety sensor
detection (Block2)
The feeder safety sensor (Block2) is detected.
0d3001
PCB position
restoration check
Please open a safety door and return PCB to the specied position of recovery
guidance. If operations are resumed without returning PCB to the specied
position, it may discharge by un-mounting.
0d3101
Component storage
box without emission
(Block1) Component storage boxes are not detected. Please install component
storage boxes.
0d3102
Component storage
box without emission
(Block2) Component storage boxes are not detected. Please install component
storage boxes.
0d3201
Feeder Base Up/Down
Operation Restrictions
(Block1)
In order to make a feeder base go up and down, please remove the stock stick
unit on a base.
0d3202
Feeder Base Up/Down
Operation Restrictions
(Block1)
Please check that the stock stick unit is not carried on a feeder base, and
perform UP/DOWN operation of a base again.
0d3203
Feeder Base Up/Down
Operation Restrictions
(Block1)
Please set “a feeder connection check / feeder serial communication” of test
operation as “Disable” for a unit check.
DEUKYX
2-21193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
0d3204
Feeder Base Up/Down
Operation Restrictions
(Block1)
Please check that Recycle Conveyor is not carried on a feeder base, and
perform UP operation of a base again.
0d3301
Feeder Base Up/Down
Operation Restrictions
(Block2)
In order to make a feeder base go up and down, please remove the stock stick
unit on a base.
0d3302
Feeder Base Up/Down
Operation Restrictions
(Block2)
Please check that the stock stick unit is not carried on a feeder base, and
perform UP/DOWN operation of a base again.
0d3303
Feeder Base Up/Down
Operation Restrictions
(Block2)
Please set “a feeder connection check / feeder serial communication” of test
operation as “Disable” for a unit check.
0d3304
Feeder Base Up/Down
Operation Restrictions
(Block2)
Please check that Recycle Conveyor is not carried on a feeder base, and
perform UP operation of a base again.
0d3401
And without substrate
transfer step without
mounting
Because there is no step installed, that does not provide a substrate transfer,
can not operate.
Simple or cancel the skip, please go to the substrate transfer.
0d3501
High Speed Head ux
coating impossible
Because you do not want to use the side view camera, can not high speed dip.
Verify the following settings, please change.
System setting : Side view camera : Use
Test run :No parts : Detected
0d3601
The appointed external
communication
Please clear the P-OUT mode.
0d3701 VM Data Error Abnormalities occurred in data expansion. Please inspect with a tester again.
0d3801
The cart for
independent production
(Block1) Test operation When you do not carry out a feeder connection check,
please raise the feeder base which carries out production use.
0d3802
The cart for
independent production
(Block2) Test operation When you do not carry out a feeder connection check,
please raise the feeder base which carries out production use.
0d3901
Unit exchange of Tray
Feeder
Please restart.
0d3a01 Comp. existence check Please turn off the Valve.
0d3b01 Check for a function The nozzle is not applicable to this operation.
0d3901
Uninstalled Brush Unit
(Block1)
Please put a brush unit on F107-F153.
0d3902
Uninstalled Brush Unit
(Block1)
Please put a brush unit on F107-F119.
0d3903
Uninstalled Brush Unit
(Block1)
Please put a brush unit on F107.
0d3904
Uninstalled Brush Unit
(Block2)
Please put a brush unit on F207-F253.
0d3905
Uninstalled Brush Unit
(Block2)
Please put a brush unit on F207-F219.
0d3906
Uninstalled Brush Unit
(Block2)
Please put a brush unit on F207.
0d3c01 Pin Recog Light (head1) The high speed head cannot move to the pin recog light.
0d3c02 Pin Recog Light (head2) The high speed head cannot move to the pin recog light.
0d3c03 Pin Recog Light (head1) The comp size is over the pin recog light spec.
0d3c04 Pin Recog Light (head2) The comp size is over the pin recog light spec.
DEUKYX
2-22193-4110
2.2 Management-Informationsliste
Code Anzeigebereich A Anzeigebereich B
0d3d01 Comp Height Ovr (head1) This function cannot use. Beause of comp height over.
0d3d02 Comp Height Ovr (head2) This function cannot use. Beause of comp height over.
0d3e01
Full detection of trash
box for component
(Block1)
Trash box for component become full. Please clean trash box for component.
0d3f01
Full detection of trash
box for component
(Block2)
Trash box for component become full. Please clean trash box for component.