TM-300_0wners_Manual - 第35页
TM-300 Ind ex 61201910. FM Page 2 of 2 TM-300 Index S safety i ntroduction 2 safety i nstructions 1 - 4 se al 12 seal assembly 27 sea l as semb ly/m otor u pright plat e 10 sea l dw ell co ntro l 24 se al pres sure ad ju…
TM-300 Index 61201910.FM Page 1 of 2
TM-300
Index
Numbers
115vac (ac power input) 13
A
adjustable loading track 9
air pressure on/off switch 9
air pressure regulator 27
air regulator 13
alarm indicator 23
alignment 27
approximate starting points
for seal controls 22
assembling procedure 6, 7
attach air supply 24
attention 3
C
carrier tape quide #1 9
carrier tape guide #2 9
carrier tape type 22
carrier tape quick lock 9
caution 4
changing the end count value
15
control module 6
control module base plate 6
control output indicator 23
controller operation 16
controller setup 17
count 12
count enable switch 14
count sensor 10
counter 12
counter controls 14
counter enable 26
counter module 14
cover tape alignment 26
cover tape guide #1 6, 9
cover tape guide #2 9
cover tape guide #3 10, 27
cover tape reel spindle 9
cover tape reel support 6
cover tape type 22
crushed hand
D
dangerous voltage 3, 4
download operation 18
drive motor 10
drive sprocket 9
dwell 12, 16
dwell setting seconds 22
E
encoder wheel 27
ent (enter) 14
error messages 23
F
feed reel support arm 6
follower track support arm 6,
10
fsw (footswitch) 13, 16
fuse 13
fwd button 11, 16
G
general seal setting informa-
tion 22
H
heat sealer 27
heat sealer assembly 10
high temperature 3
I
i/o (input/output) 13
idler arm 10
idler wheel 9
increment/decrement key
(+/-) 14, 23
initial procedures 25
inner seal 12
J
jog mode (tape adjust) 16
jog/run switch 11
L
leader 26
led deviation indicator 23
load tapes into the sealer 21
load the carrier tape 20
load the cover tape 20
loading track 27
M
main display 23
maintenance 27
marking definitions 3
mechanical assembly 9, 10
mount heat sealer assembly
19
mount take-up reel 21
N
next digit 14
O
open book 3
operation 25, 26
operation instructions 5
operating controls 11-13
outer seal 12
o-rings 19, 27
P
pc setup 18
parts cover 9
peel force 26
peripheral 13
pitch 12, 16
pitch setting guide 9
placing parts 26
power switch 11
present data indicator 23
preset 26
pressure in psi 22
pst (preset select) 14
R
rst (reset) 13, 14, 26
rev button 11, 16
rs-232 connector 13
run mode 16
TM-300 Index 61201910.FM Page 2 of 2
TM-300
Index
S
safety introduction 2
safety instructions 1-4
seal 12
seal assembly 27
seal assembly/motor upright
plate 10
seal dwell control 24
seal pressure adjust controls
9
seal pressure controls 24
seal pressure gauges 9
sealer 13
serial/parallel switch 13
setting the counter 15
setting the temperature con-
troller 23
setup 19-24
slo-syn indexer drive module
17
software download procedure
17, 18
software modification 18
start button 12
start-up procedure 16
stop button 11, 16
T
take-up reel drive arm 6
take-up reel drive motor 9
take-up reel spindle 9
tape alignment 26
tape guide #3 9
tape path 27
tape speed 12, 16
taping assembly setup 19
temperature controls 12, 23
temperature in celsius 22
tension adjust (take-up
motor) 11
to begin taping 26
to end taping 26
trailer 26
TM-300 Addendum 61170710.fm Page 1 of 1
This software modification allows additional
tape PITCH
es to be used (36, 40, 44, 48, 52
& 56mm).
To use this extended capability, the program,
‘TM300EXT.A01’, must be downloaded to the
TM-300 controller.
Follow the Software Download procedure on
page 15 of the Operator’s Manual.
Page 13 of the TM-300 Operator’s Manual
shows the index/seal capability of the current
factory default program ‘TM300.A01’
The modified program, ‘TM300EXT.A01’,
allows extended
index/seal capability (shown
below in boldface)
Substitute this extended table below for the
one located on page 13 of the Operator’s
Manual.
Example sequence of events for PITCH=56.
1. Tape sprocket advances 28mm.
2. Seal is issued.
3. Tape sprocket advances another 28mm.
4. Add one count to the counter.
5. Final Seal is issued.
Addendum
TM-300 Extended Software Modification