00191374-04 - 第23页
Adjus t ment In str uc tio ns SI PLA CE HS- 50 2 Operational Safety Edition 12/00 2.1 Safety Instruc tions 23 6DIHW\ ,QVWUXFWL RQVIRUWKH3&%%DUFRGH5H DGHU2SWLRQ .H\ CAUTION The radia nt powe r of th…
2 Operational Safety Adjustment Instructions SIPLACE HS-50
2.1 Safety Instructions Edition 12/00
22
6DIHW\,QVWUXFWLRQVIRUWKH&RPSRQHQW7DEOHV
WARNING
Never put your hands into the narrow gap between the component tables and the placement
system frame (Item. 1 in fig 2.1 - 3).
WARNING
The supply cable for the component table must not be connected or disconnected from the power
outlet of the placement system, while the component table is not docked to the machine.
(Item. 2 in fig 2.1 - 3).
WARNING
Never connect the interconnection cable of the component table to the power outlet of the
machine in order to operate the component table with the help of the compressed air control unit
outside the machine. (Item. 3 in fig 2.1 - 3)..
Adjustment Instructions SIPLACE HS-50 2 Operational Safety
Edition 12/00 2.1 Safety Instructions
23
6DIHW\,QVWUXFWLRQVIRUWKH3&%%DUFRGH5HDGHU2SWLRQ
.H\
CAUTION
The radiant power of the barcode reader‘s scanning beam is less than 1mW. This means that the
barcode reader conforms to laser class 2 and, according to DIN EN 60825-1, requires no special
safety equipment or protective measures. NEVER look into the laser beam. There is also a
safety circuit that switches off the laser diode if the polygon wheel stops or turns too slowly.
(1) PCB barcode reader
(2) Label: LASER RADIATION
(3) Label: CAUTION...
2 Operational Safety Adjustment Instructions SIPLACE HS-50
2.1 Safety Instructions Edition 12/00
24
6DIHW\,QVWUXFWLRQVIRU&KDQJLQJWKH+HLJKWRIWKH&RPSRQHQW7DEOHV
WARNING
Modification of the component table in order to change the
preadjusted table height may only be executed by trained personnel.
Act with extra care during the rearrangement, since there are
great weights and pressure springs (potential energy)
contained in the system.
&KDQJLQJWKH+HLJKWRIWKH&RPSRQHQW7DEOH
Å Use the placement system’s pneumatic controller to raise the table bed.
Å Insert a spacer block (height 120 mm) between table bed and rail and lower
the table plate onto the spacer.
Å Dismantle the internal panel.
Å Swivel down the handle.
– The latching disk will swivel down.
Å Tighten the screw to the desired dimension and use a locknut to fix it.
NOTE
If you cannot unscrew the adjusting screw to the right dimension, you must lift the rail.
Å Fix the lifting device to the rail.
Å &DUHIXOO\, open the rail clamping.
Å Lift the rail, until the end of the tube protuberates the clamping approximately 1 mm.
Å Fix the screws of the rail clamping.
Å Then, unscrew the adjusting screw to the right dimension and use a locknut to lock it.
Å Swivel up the handle of the table.
&$87,21
Laser radiation, if the cover is opene-
dand the safety interlock is bypassed.
Do not stare into laser beam!
Laser radiation
Do not stare into the laser beam
LASER CLASS 2