00196602-05_SM_SIPLACE_X-Feeder_EN - 第25页

6 Repairing the X Feeder modules 6.3 Left Side Cover Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 25 Designation Size Torque Quantity RF-SN85 2.5 x 7.5 mm 0.6 Nm 1 RF-SN75 2.5 x 6 mm 0.6 Nm 10 SN213307 M2.5x5mm 0.9…

6 Repairing the X Feeder modules

6.3 Left Side Cover

24 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017

► Lift the back of the side cover.

► Pull the side cover at a slight angle towards the

back.

Make sure that you pull the lug straight out of the

drive unit.

► Place the side cover down on a clean, safe sur-

face.

6.3.2 Fitting the Left Side Cover

► Carefully place the feeder module with the right-

side side down on a stable, level and clean sur-

face.

► (1) Lift the side cover onto the feeder module at a

slant and from the right-hand side.

(2) Make sure that the lugs insert into the drive

unit.

► (3) Make sure that the side cover is aligned with

the operating panel.

► Screw the side cover onto the feeder module, as shown in the following diagrams.

Start with screw (A) on the right, under the operating panel.

Green arrows point to the screws for which you need a TORX screwdriver with a torque of 0.6Nm.

Blue arrows point to the screws for which you need a Phillips screwdriver with a torque of 0.9Nm.

CAUTION

Do not distort the screws

When you tighten the screws, make sure that these are NOT distorted.

6 Repairing the X Feeder modules

6.3 Left Side Cover

Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 25

Designation Size Torque Quantity

RF-SN85 2.5 x 7.5 mm 0.6 Nm 1

RF-SN75 2.5 x 6 mm 0.6 Nm 10

SN213307 M2.5x5mm 0.9 Nm 5 (4+8mm)

4 (12mm)

DIN965 M2.5x5mm 0.9 Nm 3

SN213307 M2.5x3mm 0.9 Nm 5

RF-SN75 2.5 x 6 mm - 1

(X) The screw (X) varies between the different feeder modules.

In 4 - 8mm feeder modules, this is a screw of type (D).

In 12mm feeder modules, this is a screw of type (C).

CAUTION

The screw marked F is easily damaged

Tighten the screw marked (F) carefully with a small Phillips screwdriver.

Make sure that this screw is NOT distorted.

6 Repairing the X Feeder modules

6.3 Left Side Cover

26 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017

Designation Size Torque Quantity

RF-SN85 2.5 x 7.5 mm 0.6 Nm 1

RF-SN75 2.5 x 6 mm 0.6 Nm 4

SN213307 M2.5x5mm 0.9 Nm 11

ISO7046 M2.5x6mm 0.9 Nm 3

SN213307 M2.5x4mm 0.9 Nm E

For 4-12mm feeder modules only

► Now fit the rear sliding guide onto the feeder (see 6.2.2 "Fitting the Rear Sliding Guide" [}22]).