00196602-05_SM_SIPLACE_X-Feeder_EN - 第59页
6 Repairing the X Feeder modules 6.5 Foil Disposal Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 59 ► Carefully place the feeder module down on its left side. ► Fix the ratchet with the mushroom head cutting screw (T…
6 Repairing the X Feeder modules
6.5 Foil Disposal
58 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
6.5.5.2 Fitting the Ratchet (4 - 12 mm)
► Insert the connector through the opening in the
ratchet.
► Plug the connector into the connection shown in
the diagram.
Make sure that the smooth side of the connector
is at the top.
► Push the ratchet sideways under the small board,
as far as the foil disposal drive.
Make sure that the left side of the ratchet is
against the tape duct.
► Fix the ratchet first with the top cylinder head
screw (2.5x10mm).
Do not tighten the screw fully as you still need to
move the ratchet slightly.
► Fix the ratchet into place with the bottom cylinder
head screw (2.5x10mm).
► Now tighten the top screw.
► Run the cable as marked in the diagram.
► Fix the cable with the rubber seal.
Make sure that the rubber seal does not project
beyond the holder.
► Make sure that the corresponding washers are
on the toothed wheel axes (2).
► Place the cover plate onto the foil disposal drive.
Make sure that the cover plate engages at the
toothed wheel axes (3).
► Fix the cover plate with the countersunk screws
marked in the diagram (M2.5 x 5mm).
► Then fit the left side cover into place (see 6.3.2
"Fitting the Left Side Cover" [}24]).
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 59
► Carefully place the feeder module down on its left
side.
► Fix the ratchet with the mushroom head cutting
screw (T2.5x6mm) marked in the diagram.
6.5.5.3 Removing the Ratchet (16 - 88 mm)
► First remove the rocker (see 6.6.2 "Rocker Assembly" [}68]).
► Carefully place the feeder module down on its left side.
► Remove the screws shown in the following diagram.
Diagram of X feeder modules with 16mm width
Diagram of X feeder modules with 24-88mm width
6 Repairing the X Feeder modules
6.5 Foil Disposal
60 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
► Carefully place the feeder module on its right
side.
► Remove the left side cover (see 6.3.1 "Removing
the Left Side Cover" [}23]).
► Now loosen the screws marked in the diagram.
Screw (1) should only be loosened for X feeder
modules with 16mm width.
► Remove the spacer from the feeder module.
► (1) Pull the connector marked in the diagram up
and out of its connection.
To loosen the connector, move it carefully from
side to side.
► (2) Pull the connector marked in the diagram out
of its connection in the direction of the arrow. Pull
on the connector and NOT on the cable.
► (3) Carefully swing the lock on the flat ribbon
cable connection up to the left and release the
flat ribbon cable.
Make sure that the lock is not pushed too far
back. It could break off if you do this.
► Pull the connector shown in the diagram out of its
connection in the direction of the arrow. Pull on
the connector and NOT on the cable.
► Remove the foil drive, together with the foil con-
tainer, out of the feeder module.
For 16mm feeder modules only
► Turn the foil disposal drive over, together with the
foil container.
► Loosen the screw marked in the diagram.
► Turn the foil disposal drive over again.