00196602-05_SM_SIPLACE_X-Feeder_EN - 第60页

6 Repairing the X Feeder modules 6.5 Foil Disposal 60 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 ► Carefully place the feeder module on its right side. ► Remove the left side cover (see 6.3.1 "Removing the Le…

100%1 / 90
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 59
► Carefully place the feeder module down on its left
side.
► Fix the ratchet with the mushroom head cutting
screw (T2.5x6mm) marked in the diagram.
6.5.5.3 Removing the Ratchet (16 - 88 mm)
► First remove the rocker (see 6.6.2 "Rocker Assembly" [}68]).
► Carefully place the feeder module down on its left side.
► Remove the screws shown in the following diagram.
Diagram of X feeder modules with 16mm width
Diagram of X feeder modules with 24-88mm width
6 Repairing the X Feeder modules
6.5 Foil Disposal
60 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
► Carefully place the feeder module on its right
side.
► Remove the left side cover (see 6.3.1 "Removing
the Left Side Cover" [}23]).
► Now loosen the screws marked in the diagram.
Screw (1) should only be loosened for X feeder
modules with 16mm width.
► Remove the spacer from the feeder module.
► (1) Pull the connector marked in the diagram up
and out of its connection.
To loosen the connector, move it carefully from
side to side.
► (2) Pull the connector marked in the diagram out
of its connection in the direction of the arrow. Pull
on the connector and NOT on the cable.
► (3) Carefully swing the lock on the flat ribbon
cable connection up to the left and release the
flat ribbon cable.
Make sure that the lock is not pushed too far
back. It could break off if you do this.
► Pull the connector shown in the diagram out of its
connection in the direction of the arrow. Pull on
the connector and NOT on the cable.
► Remove the foil drive, together with the foil con-
tainer, out of the feeder module.
For 16mm feeder modules only
► Turn the foil disposal drive over, together with the
foil container.
► Loosen the screw marked in the diagram.
► Turn the foil disposal drive over again.
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 61
► Remove the rubber seal marked in the diagram
(1).
► Loosen the screws marked in the diagram (2).
► Lift the cover plate off the foil disposal drive.
Example diagram of 16mm feeder module
► Loosen the two screws marked in the diagram.
► Carefully pull the ratchet to the left, away from
the foil disposal drive.
► Remove the cable from the opening in the
ratchet.
The ratchet is now free.
6.5.5.4 Fitting the Ratchet (16 - 88 mm)
Example diagram of 16mm feeder module
► Insert the connector through the opening in the
ratchet.
► Push the ratchet sideways under the small board,
as far as the foil disposal drive.
► Fix the ratchet first with the top cylinder head
screw (2.5x10mm).
Do not tighten the screw fully as you still need to
move the ratchet slightly.
► Fix the ratchet into place with the bottom cylinder
head screw (2.5x10mm).
► Now tighten the top screw.
► Run the cable as marked in the diagram.