00196602-05_SM_SIPLACE_X-Feeder_EN - 第64页
6 Repairing the X Feeder modules 6.5 Foil Disposal 64 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 ► Carefully place the feeder module down on its left side. ► Position the foil container so that it is aligned again…
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 63
► Insert the foil disposal drive, together with the foil
container, into the feeder module.
► (1) Insert the flat ribbon cable into the connection,
as far as the stop.
Make sure that the blue surface at the end of the
cable is at the top and that the flat ribbon cable
lies straight in the connection.
► Swing the lock on the connection down onto the
flat ribbon cable.
Make sure that the flat ribbon cable is fitted firmly
in the connection. Tug gently on the cable to
check.
► Check again whether the flat ribbon cable is fitted
straight in the connection.
If necessary, open the lock and correct the posi-
tion of the cable before closing the lock again.
► (2) and (3)
Carefully insert the connector in the direction of
the arrow, as far as the stop, into the connection
shown.
Make sure that the smooth side of the connector
is at the top.
CAUTION!
Do not push the connector with force into the
connection, otherwise individual pins may
break off or be distorted.
.
► (4) Insert the other connector into the connection
marked in the diagram.
► Push the spacer from the right in the direction of
the arrow, around the rubber seal.
► Fix the spacer with the screws marked in the dia-
gram.
Note: screw (1) only used for 16mm feeder mod-
ules.
(1) Cylinder head Phillips screw with washer
(2) Mushroom head cutting screw (Torx long)
(3) Countersunk cutting screw (Torx short)
► Fit the left side cover into place (see 6.3.2 "Fitting
the Left Side Cover" [}24]).
6 Repairing the X Feeder modules
6.5 Foil Disposal
64 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
► Carefully place the feeder module down on its left
side.
► Position the foil container so that it is aligned
against the side cover.
Diagram of X feeder modules with 16mm width
► Fix the mushroom head cutting screws marked in
the diagram (2.5 x 7.5mm) Torx.
► Now fit the rocker (see 6.6.2.2 "Fitting the Rocker
(4 - 88 mm)" [}70]).
Diagram of X feeder modules with 24-88mm width
► Loosen the screws marked in the diagram.
(1) Mushroom head cutting screw (2.5x7.5mm)
Torx
(2) Cylinder head Phillips screw (2.5x5mm)
► Now fit the rocker (see 6.6.2.2 "Fitting the Rocker
(4 - 88 mm)" [}70]).
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 65
6.5.6 Tape Disposal Flap
Required spare parts
Fig.3: Example: foil disposal flap 8mm X
Fig.4: Example: foil disposal flap 24mm X
Feeder module Item no. Designation
4 mm 03088304-xx Foil disposal flap X4
8 mm 03003124-xx Flap / tape disposal X8
12 mm 03006127-xx Flap / tape disposal X12
16 mm 03096848-xx Flap / tape disposal X16
24 mm 03085750-xx Flap / tape disposal X24
32 mm 03085752-xx Flap / tape disposal X32
44 mm 03085790-xx Flap / tape disposal X44
56 mm 03085763-xx Flap / tape disposal X56
72 mm 03085772-xx Flap / tape disposal X72
88 mm 03085782-xx Flap / tape disposal X88
Required tools
●
Universal pliers
6.5.6.1 Removing the Flap (4–12mm)
► Remove the left side cover (see 6.3.1 "Removing
the Left Side Cover" [}23]).
► Pull the spindle out of the flap. Use universal pli-
ers for this.
► Remove the flap sideways from the feeder mod-
ule.