00196602-05_SM_SIPLACE_X-Feeder_EN - 第82页
6 Repairing the X Feeder modules 6.7 Operating Panel Assembly 82 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 For 16-24mm feeder modules only ► Lift the foil disposal, together with the foil con- tainer, out of t…
6 Repairing the X Feeder modules
6.7 Operating Panel Assembly
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 81
6.7.5 Removing the Operating Panel (16 - 88 mm)
► Carefully place the feeder module down on its left side.
► Remove the screws shown in the following diagram.
Example diagram for X feeder modules with 16mm
width
Example diagram for X feeder modules with 24 -
88mm width
► Now carefully place the feeder module down on its right-hand side.
► Remove the left side cover (see 6.3.1 "Removing the Left Side Cover" [}23]).
► (1) Pull the connector marked in the diagram up
and out of its connection.
To loosen the connector, move it carefully from
side to side.
► (2) Pull the connector marked in the diagram out
of its connection in the direction of the arrow. Pull
on the connector and NOT on the cable.
► (3) Carefully swing the lock on the flat ribbon
cable connection up to the left and release the
flat ribbon cable.
Make sure that the lock is not pushed too far
back. It could break off if you do this.
► Pull the connector shown in the diagram out of its
connection in the direction of the arrow. Pull on
the connector and NOT on the cable.
6 Repairing the X Feeder modules
6.7 Operating Panel Assembly
82 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
For 16-24mm feeder modules only
► Lift the foil disposal, together with the foil con-
tainer, out of the feeder module.
► Remove the two screws shown in the left-hand
diagram (1).
► Turn the foil disposal drive over, together with the
foil container.
► Remove the two screws shown in the right-hand
diagram (2).
► Loosen the marked screws (3), so that the oper-
ating panel can be moved. One complete rotation
should be sufficient.
If you are still unable to move the operating
panel, loosen the two screws by a further rota-
tion.
For 32-88mm feeder modules only
► Lift the foil disposal, together with the foil con-
tainer, out of the feeder module.
► Remove the two screws shown in the left-hand
diagram (1).
► Loosen the marked screws (2), so that the oper-
ating panel can be moved. One complete rotation
should be sufficient.
If you are still unable to move the operating
panel, loosen the two screws by a further rota-
tion.
► Turn the foil disposal drive over, together with the
foil container.
► Remove the two screws shown in the right-hand
diagram (3).
When using wider feeder modules, you need a
longer Torx screwdriver size 8.
► Turn the foil disposal drive over, together with the
foil container.
► (1) Press the removal handle so that this springs
out.
► (2) Lift the operating panel up and out of the foil
container frame.
6 Repairing the X Feeder modules
6.7 Operating Panel Assembly
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 83
► Pull both cables out of the foil container frame.
6.7.6 Fitting the Operating Panel (16 - 88 mm)
► Thread the cable through the slit in the foil con-
tainer frame, as marked in the diagram.
► (1) Push the front part of the control panel as far
as the stop into the slit in the foil container frame.
► (2) Pull the control panel towards the foil con-
tainer.
► (3) Press the release handle into the control
panel.