YG100R_Ope_E - 第4页
3 . S t a r t i n g a n d s t o p p i n g t h e m a c h i n e 2 - 1 6 3 . 1 P r e - o p e r a t i o n c h e c k 2 - 1 7 3 . 2 S t a r t i n g t h e m a c h i n e 2 - 1 8 3 . 3 Wa r m i n g u p t h e m a c h i n e 2 - 2 0…
Chapter 1 Part names and functions
1. Machine main unit 1-1
2. Operation panel and data input unit 1-
4
2.1 Keyboard and mouse 1-4
2.2 Operation panel buttons 1-
5
3. Head assembly 1-6
3.1 Component pick-and-place head 1-6
3.1.1 Eight-in-line multi-head (FNC) assembly 1-6
3.1.2 Eight-in-line multi-head (standard) assembly 1-7
3.2 Nozzle types 1-8
3.2.1 Nozzles for the eight-in-line head assemblies 1-8
3.3 Nozzle station (option) 1-9
4. Component supply section 1-10
4.1 Supplying components from feeder plates 1-10
4.1.1 Fixed feeder plates 1-10
4.1.2 Feeder exchange carriage 1-11
4.2 Supplying components from trays 1-13
4.2.1 dYTF main unit 1-13
4.2.2 sATS main unit 1-15
4.2.3 wATS main unit 1-17
5.
Conveyor unit and component recognition system
1-19
6. Axis configuration 1-2
0
7. Blow station 1-2
1
7.1 Performing a nozzle shaft blow 1-22
8. Other options 1-23
8.1 Side-view camera 1-23
8.2 QFP dump station 1-2
4
Chapter 2 Basic operation
1. Before operation 2-1
1.1 Canceling emergency stop 2-1
1.2 Clearing an error 2-
2
1.3 Typical errors and troubleshooting 2-
3
2. Operation screen and buttons 2-8
2.1 Basic configuration of operation screen 2-8
2.2 Setup screen 2-1
0
2.3 Unit screen 2-1
1
3. Starting and stopping the machine 2-16
3.1 Pre-operation check 2-17
3.2 Starting the machine 2-1
8
3.3 Warming up the machine 2-2
0
3.4 Adjusting the conveyor unit setup 2-2
2
3.4.1 Conveyor unit setup flow 2-22
3.4.2 Conveyor width 2-23
3.4.3 Board hold plates 2-24
3.4.4 Push-up pins 2-25
3.5 Preparing the component supply unit 2-26
3.5.1 Tape feeder 2-26
3.5.2 Tray changer 2-31
Chapter 3 Starting and ending production
1. Starting production 3-1
1.1 Resuming operation from the stopped point 3-4
1.1.1 Loading the saved data 3-4
1.1.2 Editing mount flags 3-5
2. Ending production and turning power off 3-6
3. Displaying the production monitors 3-
8
3.1 Main 3-8
3.2 Detail 3-1
0
3.3 Vision 3-1
2
3.4 Alignment 3-1
4
3.5 Retry 3-1
5
3.6 Fiducial 3-1
5
3.7 Badmark 3-1
6
3.8 Pick Pos. (Pickup position offset) 3-1
7
3.9 Pick Rate Warning 3-1
8
3.10 Coplanarity checker (YG100R and YG88R only) 3-2
1
Appendix
A1. Specifications A-1
Index
About this manual
The instruction manual of this machine is written for those who operate
this machine.
Please read this manual carefully for correct operations and pay
special attention to safety precautions.
After reading through this manual, please use this manual as an
occasional reference and keep it within reach.
About this manual
Contents
1. Using this manual i
1.1 Available manuals i
1.2 Manual contents ii
2. Contents of each chapter iii
3. Page layout iv