YSM10_Mainte_E - 第72页
3-5 3 Periodic maintenance items 1.2.4 ANC nozzle attaching / detaching tool Regarding the machine equipped with a nozzle station (option / hereafter "ANC"), nozzles are detac hed manually from the nozzle stati…
3-4
3
Periodic maintenance items
1.2.2 Cleaning the nozzle air path
e
1
Remove the nozzle from the head.
1. Press the emergency stop button to open
the machine safety cover.
2. Remove the nozzle from the head. If the
machine is equipped with the nozzle
station, press the [Nozzle Stn Shutter]
button to open the nozzle station shutter
and remove the nozzle.
2
Blow air through the nozzle.
1. Detach the nozzle tip.
2. Blow air from the nozzle attachment side.
2. Attach the nozzle tip and blow air from
the nozzle attachment side.
53305-KMG-00
c
CAUTION
Make sure not to deform the clip.
n
NOTE
If there are dust deposits in the nozzle, perform steps 3
and 4.
3
Clean the nozzle hole.
1. Pass a nozzle cleaning wire through the
nozzle hole.
2. Clean the nozzle by moving it as shown
at right.
53306-KMG-00
4
Blow air onto the nozzle tip again.
Remove the nozzle cleaning wire, then
air-blow the nozzle interior with the air blow
tool as described in Step 2.
5
Return the nozzle to its original
position.
Return the nozzle to the head or nozzle
station where the nozzle was removed.
1.2.3 Cleaning the nozzle tip
A little dirt at the nozzle tip can be cleaned up with the "Nozzle tip cleaning tape" that comes with the
machine.
n
Nozzle tip cleaning procedures
Push the nozzle tip against the adhesive surface of the "Nozzle tip cleaning tape" vertically several times to remove the
contaminants.
n
When using the ultrasonic cleaner (option)
Clean the nozzle with the ultrasonic cleaner.
Even when contaminants are not removed completely using the ultrasonic cleaner (option), performing the work shown
above after cleaning will be effective.
Cleaning a nozzle
Step 3
Nozzle
Nozzle cleaning wire
Air blow
Step 2
Air blow unit (optional)
Remove the clip.
Pull out the pin.
Air tube (orange) connected
to air supply port
■ Detach the nozzle tip, and
air-blow from that side.
■ Attaching/detaching the nozzle tip
■ Blow air from the nozzle
attachment side.
3-5
3
Periodic maintenance items
1.2.4 ANC nozzle attaching / detaching tool
Regarding the machine equipped with a nozzle station (option / hereafter "ANC"), nozzles are detached
manually from the nozzle station for maintenance. In this case, if using the "ANC nozzle attaching / detaching
tool" (hereafter "tool"), up to 10 nozzles can be attached / detached at once.
Nozzles are not attached Nozzles are attached (use it facing down)
ANC nozzle attaching / detaching tool
Tool tip protecting cap
ANC nozzle attaching / detaching tool
30x, 31x series nozzles
53307-KMG-00
n
Available nozzles
30x series nozzles (301A, 303A nozzles, etc.) and 31x series nozzles (311A, 312A nozzles, etc.)
n
NOTE
The "Tool tip protecting cap" is attached on the tip of the tool when shipping the tool. Make sure to attach the cap
except when the tool is used for protection.
3-6
3
Periodic maintenance items
n
How to use ANC nozzle attaching / detaching tool (detaching nozzles)
1
Open the nozzle station shutter.
Open the [Unit] - [Head] screen and press
the [Nozzle. Stn Shutter] button to open the
nozzle station shutter.
54300-KMG-00
2
Set the tool on the nozzle station.
1. Press the emergency stop button to open
the machine safety cover.
2. Set the tool vertically on the nozzles at
the nozzle station aligning the position of
nozzles to be detached.
3. Check that the tool is set to nozzles
securely.
53308-KMG-00
3
Raise the tool up.
Raise the tool up vertically and slowly.
53309-KMG-00
n
NOTE
Raise the tool up vertically and slowly to avoid the
nozzle tip from hitting the shutter, etc.
c
CAUTION
If raising the tool up fast and forcibly, nozzles or the
nozzle station may be damaged.
4
Close the nozzle station shutter.
Press the [Nozzle. Stn Shutter] button again
and close the nozzle station shutter.
Nozzle station - Opening the shutter
[Nozzle.Stn Shutter] button
Step1
Step 2
Setting the tool
Set the tool vertically aligning
nozzles to be detached.
Check that the tool is set to
nozzles securely.
Step 3
Raising the tool up
Raise the tool up vertically to avoid the
nozzle tip from hitting the shutter.