YG300_Mainte_E - 第37页

2-7 2 Daily maintenance items 5 . C l e a n i n g t h e c a m e r a t r a n s p a r e n t c o v e r D i r t o r d u s t p a r t i c l e s s t i c k i n g t o t h e t r a n s p a r e n t c o v e r o f t h e m u l t i - v …

100%1 / 72
2-6
2
Daily maintenance items
4. Cleaning the feeder plate
Clean the feeder plate by using the brush supplied with the machine. Chips or foreign matter falling on
the feeder plate might bite into the surface during feeder setting and cause the pickup position to deviate.
Periodic inspection and cleaning are recommended to prevent this problem.
Chips
Chips adhering to the bottom
of a tape feeder
Cleaning brush
Cleaning the feeder plate
53205-F1-00
Reference
You can clean chips and debris on the feeder plate while dropping them into the holes in the rear of the feeder plate.
2-7
2
Daily maintenance items
5. Cleaning the camera transparent cover
Dirt or dust particles sticking to the transparent cover of the multi-view camera can cause recognition errors.
Periodic inspection and cleaning are recommended to prevent this problem.
e
To ensure safety, make sure that the machine power switch is off or the emergency stop button is pressed
before starting work.
1
Remove dust on the transparent
cover with the lens blower brush.
53206-F1-00
Reference
A lens blower brush is available as an option.
2
Wipe the transparent cover with a
lint-free cloth.
Apply a few drops of lens cleaner to a
lint-free cleaning cloth or paper towel and
wipe the transparent cover.
53207-F1-00
n
NOTE
Use a lint-free cleaning cloth or paper wiper.
A lens cleaner is available as an option.
Blowing off dust with blower brush
Step 1
Lens blower brush
Wiping the transparent cover
Step 2
Lent-free cleaning cloth or paper wiper
Chapter 3 Periodic maintenance items
Contents
1. Weekly inspection 3-1
1.1 Cleaning nozzles 3-1
2. Monthly inspection 3-3
2.1 Inspecting ball screws and linear guides of each axis 3-3
2.2 Cleaning and lubricating a nozzle holder 3-
4
2.3 Cleaning and greasing the X-axis 3-
6
2.3.1 Cleaning and greasing the X-axis ball screws 3-6
2.3.2 Cleaning and greasing the X-axis linear guides 3-8
2.4 Cleaning and greasing the Y-axis 3-9
2.4.1 Cleaning and greasing the Y-axis ball screws 3-9
2.4.2 Cleaning and greasing the Y-axis linear guides 3-10
2.5 Cleaning and greasing the U-axis 3-12
2.5.1 Cleaning and greasing the U-axis ball screws 3-12
2.5.2 Cleaning and greasing the U-axis linear guides 3-13
2.6 Cleaning and greasing the W-axis 3-14
2.6.1 Cleaning and greasing the W-axis ball screws 3-14
2.6.2 Cleaning and greasing the W-axis linear guides 3-15
2.7 Cleaning and greasing the T-axis 3-16
2.7.1 Cleaning and greasing the T-axis ball screws 3-16
2.7.2 Cleaning and greasing the T-axis linear guides 3-17
2.8 Cleaning and greasing the Z-axis 3-18
2.9 Inspecting and cleaning the air/mist filters 3-1
9
2.10 Cleaning the camera lens and lighting unit 3-2
1
3.
3-month, 6-month or one-year inspection
3-23
3.1 Cleaning and replacing the ejector filter 3-23
3.2 Cleaning and lubricating the inside of the spline shaft 3-2
4
3.2.1 Cleaning the inside of the spline shaft 3-24
3.2.2
Lubricating the slide section and checking the negative pressure
3-26